Abstract:This paper presents characterization and compensation of the thermal bias drift of a MEMS accelerometer whose effective stiffness is electrostatically tuned to a low value with the help of the single-sided parallel plates (SSPPs) capacitors. A temperature drift model for the proposed accelerometer is built and the temperature effect on the mechanical stiffness and the circuit gains is characterized. The characterization reveals that the variations of the feedforward coefficient including the mechanical stiffness and the readout gain due to the temperature change play a significant role in the bias drift of output of the proposed closed-loop accelerometer. On the other hand, the variations of both feedback gain and tuning gain as a function of temperature are one-order-of-magnitude less than that of the feedforward coefficient. To calibrate the feedforward coefficient, an excitation signal as a form of AC reference displacement is introduced to drive the proof mass and the readout response is demodulated to calibrate the variance of the feedforward coefficient correspondingly. An open-loop compensation scheme for the temperature-induced bias drift using the variance of the calibrated response is proposed accordingly. Alternatively, the calibrated response can be controlled to a preset value by a new proportion integral derivative (PID) controller by the adjustment of the SSPP tuning voltage. The output of the PID controller is used for the calibration of the introduced bias from the electrostatic tuning force. Therefore, a closed-loop compensation of the thermal bias drift is achieved by remaining the feedforward coefficient while eliminating the calibrated bias. Experiments under a temperature cooling process and different tuning voltages are carried out to verify two proposed compensation schemes. The temperature drift coefficients (TDCs) of both compensated outputs exhibit at least one-order-of-magnitude reduction in response to the temperature change. When the effective stiffness of the accelerometer is tuned to about 4.19 N m(-1), the TDC of the compensated output using the proposed open-loop or closed-loop compensation schemes is reduced to about 0.1136 or 0.0391 mg degrees C-1, respectively and meanwhile, the Allan bias instability is slightly increased to 48.63 or 56.14 mu g, respectively.

Analyses on bias drift due to mode parameter variations of micromachined vibratory gyroscope

Analysis of the Frequency-Dependent Vibration Rectification Error in Area-Variation-Based Capacitive MEMS Accelerometers.

Effects of Structural Dimension Variation on the Vibration of MEMS Ring-Based Gyroscopes

The Analysis of Temperature Effect and Temperature Compensation of Moems Accelerometer Based on A Grating Interferometric Cavity

Analysis and Compensation of Bias Drift for a Micromachined Spinning-rotor Gyroscope with Electrostatic Suspension.

Identification and Suppression of Driving Force Misalignment Angle for a MEMS Gyroscope Using Parametric Excitation

Noise Analysis and Modeling for a Digital Control Architecture for Lissajous Frequency-Modulated MEMS Gyroscope with Amplitude-Modulated Readout

Effects Of Both The Drive- And Sense-Mode Circuit Phase Delay On Mems Gyroscope Performance And Real-Time Suppression Of The Residual Fluctuation Phase Error

Characterization and Compensation of Thermal Bias Drift of a Stiffness-Tunable MEMS Accelerometer

Temperature drift suppression for micro‐electro‐mechanical system gyroscope based on vibrational‐displacement control with harmonic amplitude ratio

Mems Gyroscope Bias Drift Self-Calibration Based On Noise-Suppressed Mode Reversal

Modeling and Reliability Analysis of MEMS Gyroscope Rotor Parameters under Vibrational Stress

Analysis of In-Phase Coupling Error in the Vibratory MEMS Gyroscope with Various Vacuum Degrees

Improving Long-Term Stability of a Resonant Micro-Optic Gyro by Reducing Polarization Fluctuation

Bias Modulation of Force-to-Rebalanced Micro Hemispherical Resonator Gyroscope Based on Mode-Rotation

A sub 0.8 degree per hour mode-matching MEMS vibratory gyroscope with closed loop control for the sense mode

Closed loop control design for the sense mode of micromachined vibratory gyroscopes

A Temperature Drift Suppression Method of Mode-Matched MEMS Gyroscope Based on a Combination of Mode Reversal and Multiple Regression

Resonance asymmetry induced bias errors in waveguide type optical passive resonator gyro.

Temperature Drift Compensation for Four-Mass Vibration MEMS Gyroscope Based on EMD and Hybrid Filtering Fusion Method

MEMS Gyroscope Temperature Compensation Based on Drive Mode Vibration Characteristic Control