Abstract:Organic photovoltaic solar cells can offer advantages of being mechanically flexible and durable, large area devices, lightweight, made from a diversity of materials and low-cost fabrication. Their efficiency is, however, still too low for commercial exploitation. Empirical observations reveal that polymer–fullerene (P3HT:PCBM) based solar cell performance depends on thermal annealing processes employed, especially the annealing temperatures and durations. The annealing parameters are known to influence the energetics and kinetics of the blending process or morphology, but the associated physics is not fully understood. In this work, current density–voltage characteristics of P3HT:PCBM bulk heterojunction organic solar cells, thermally annealed at different temperatures, 65–160 °C post fabrication, were investigated under dark and illuminated conditions, and compared to their as-cast counterparts. In certain electrical regimes, as-cast devices showed higher values of current density in comparison to the corresponding annealed devices. Such performance was attributed to air-borne chemical doping of the as-cast semiconductor layer, which creates electrically conductive percolation pathways within the as-cast devices. We propose that annealing of semiconductors must be a two-step process, which first initiates decrease in conductivity, followed by its increase. As-cast devices P3HT–PCBM bulk heterojunction solar cells prepared under atmospheric conditions were observed to have comparatively superior photovoltaic performance in comparison to thermally annealed devices. The efficiency drop in the annealed counterparts is attributed to dedoping due to thermal annealing. An annealing temperature of ~ 140 °C was found to be optimum for power conversion efficiency in the bulk heterojunction, 1:1 by mass, P3HT:PCBM based solar cells.

Optimisation of Thermal Annealing Parameters for Different Thickness of Active Layers Based on Polymer/fullerene Bulk Heterojunction Solar Cells

Analysis of the Effect of Active Layer Thickness on Polymer Solar Cell Performance Based on Optical and Opto-Electronic Model

Dark and illuminated J(V) characteristics of thin layered bulk heterojunction P3HT:PCBM sandwich solar cells after thermal treatment

Charge transport and extraction of PTB7:PC71BM organic solar cells: effect of film thickness and thermal-annealing

Determination of optical constants and thickness of photoactive layer in polymer oslar cells by single transmission measurement

Inverted All-Polymer Solar Cells Based on a Quinoxaline–thiophene/naphthalene-Diimide Polymer Blend Improved by Annealing

Influence of thermal annealing on microstructure, energetic landscape and device performance of P3HT: PCBM-based organic solar cells

Post-Fabrication Annealing Effects in Polymer-Nanotube Photovoltaic Cells

Quantitative Nanoscale Monitoring the Effect of Annealing Process on the Morphology and Optical Properties of Poly(3-Hexylthiophene)/[6,6]-phenyl C61-butyric Acid Methyl Ester Thin Film Used in Photovoltaic Devices

High Performance Solar Cell Based on Ultra-Thin Poly(3-Hexylthiophene): Fullerene Film Without Thermal and Solvent Annealing

Annealing Effects on the Photovoltaic Performance of All-Conjugated Poly(3-Alkylthiophene) Diblock Copolymer-Based Bulk Heterojunction Solar Cells

Optimization of Bulk Heterojunction Organic Photovoltaics

The improvement of bulk-heterojunction order in polymer photovoltaic device.

Improvement of Surface Morphology of Thin ?lms and Performance by "electrical Annealing" on Polymer Solar Cells

Thermal Annealing Effect on Ultrafast Charge Transfer in All-Polymer Solar Cells with a Non-Fullerene Acceptor N2200

Thermal Radiation Annealing for Overcoming Processing Temperature Limitation of Flexible Perovskite Solar Cells

Highly Efficient Solar Cells Based on the Copolymer of Benzodithiophene and Thienopyrroledione with Solvent Annealing

Thermal-Induced Performance Decay of the State-of-the-Art Polymer: Non-Fullerene Solar Cells and the Method of Suppression

Study of the effect of annealing process on the performance of P3HT/PCBM photovoltaic devices using scanning-probe microscopy

Performance improvement of annealing-free P3HT : PCBM-based polymer solar cells via 3-methylthiophene additive

High-efficiency CdTe-based Thin-Film Solar Cells with Unltrathin CdS:O Window Layer and Processes with Post Annealing