Abstract:The hardness, tensile ductility and fatigue lifetime of nanostructured (NC) Cu–Zr alloyed thin films have been systematically measured at different Zr additions (0, 0.5, 2.0, 4.0, 8.0at.%). Experimental results showed that the Cu–0.5at.% Zr film exhibited the highest hardness, largest ductility and longest fatigue lifetime, which are increased by 120%, 80%, and above an order of magnitude, respectively, in comparison with its pure Cu counterpart. The simultaneous improvements of mechanical properties are rationalized with respect to microstructural evolutions related to Zr segregation at grain boundaries (GBs). Besides refinement in NC grains and enhancement in nanotwins, grain orientation was apparently modified by the GB Zr segregation. (110) grains were promoted and layer-like microstructure was formed with coexistence of three orientation of grains at the upper layer, facilitating Cu grain growth at room temperature. GB doping strengthening worked as an additional strengthening mechanism and mechanically driven grain growth became the predominant deformation mechanism and fatigue mechanism, which accounted for the optimal combination of mechanical properties achieved in the Cu–0.5at.% Zr film. When the Zr content was >2.0at.%, however, amorphous phases were formed at the GBs due to locally increased Zr concentration. The GB doping strengthening effect was concomitantly weakened and strength was gradually decreased. In addition, stress/strain localization occurred readily at the amorphous phase regions, triggering intergranular fracture and reducing ductility. During cyclic testing in the low stress range, GB amorphous phases strengthened rather impaired the GBs, which gave the Cu–Zr films a fatigue lifetime greater than that of the pure NC Cu film. The present results clearly indicate that, once solute content is suitably explored, the solute segregation at GBs in NC metals can not only retain NC grains in loading-free conditions, but also impart enhanced mechanical properties when exposed to applied stress.

Tailoring Grain Size Distribution for Optimizing Strength and Ductility of Multi-Modal Zr

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

Microstructure‐Property Relations in the Tensile Behavior of Bimodal Nanostructured Metals

Constitutive modeling of mechanical behaviors in gradient nanostructured alloys with hierarchical dual-phased microstructures

Tailoring bimodal grain structure of Mg-9Al-1Zn alloy for strength-ductility synergy: Co-regulating effect from coarse Al2Y and submicron Mg17Al12 particles

Superior mechanical properties of pure Zr with heterogeneous structure

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Development of bimodal grain-structured Al-Zn-Mg-Cu-Zr alloys for strength-ductility synergy via microalloying with Hf and Sc

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructural Evolution, Mechanical Properties and Deformation Mechanisms of Nanocrystalline Cu Thin Films Alloyed with Zr

The effect of grain size on deformation modes and deformation heterogeneity in a rolled Mg-Zn-Ca alloy

Achieving superior strength and ductility synergy in bulk ultrafine grained Al-Mg-Sc-Zr alloy via powder pre-aging

Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy

Tailoring strength and ductility of Mg97Y2Zn1 alloy through the architecture of heterogeneous lamellar structure by large-ratio hot extrusion

Grain Refinement Enhanced Tensile Strength, Fracture Toughness and Fatigue Crack Propagation Resistance of a High Zn-Containing Al-Zn-Mg-Cu Alloy

Achieving synergy enhancement of strength and ductility in Ti-6Al-2Sn-4Zr-2Mo-0.1Si alloy by fabricating a new multiscale microstructure

Achieving Excellent Strength–Ductility Synergy by Tailoring the Grain Size Distribution in a Metastable Austenitic Stainless Steel

Tailoring grain refinement through thickness in magnesium alloy via stationary shoulder friction stir processing and copper backing plate

Manipulating nanostructure to simultaneously improve the electrical conductivity and strength in microalloyed Al-Zr conductors

Revealing the High Strength and High Thermal Stability of a Nano-Lamellar Cu-0.1 At. % Zr Alloy

Optimization of multi-directional forging parameters of large-scale Mg-Gd-Y-Zn-Zr alloy forged part guided by finite element simulation