Abstract:Studying the tribological behavior between diamond materials and ceramics is crucial for understanding the grinding mechanism of diamond wheels on ceramics. To comprehend the tribological characteristics between diamond materials and various ceramics, this paper presents a comparative study of the tribological behaviors of Al2O3, AlN, Si3N4, and ZrO2 ceramics sliding against polycrystalline diamond (PCD) balls. The dependence of the coefficient of friction (COF), wear characteristics as well as the surface morphology of different ceramics and SiC-bonded PCD balls on load, sliding stage were examined. The effect of nanofluids on the COF and wear of different ceramics was also investigated. The results showed that the tribological characteristics of ceramic materials are strongly dependent on mechanical properties. Al2O3 and AlN ceramics with lower fracture toughness exhibit a significantly higher COF and wear volume than that of Si3N4 and ZrO2 ceramics. Al2O3 presents the highest COF (0.38) and wear volume, and Si3N4 owns the lowest COF (0.08) and wear volume under the load of 9.8 N. By examining the wear grooves of different ceramics, it is found that Al2O3 and AlN ceramics own larger debris than that of Si3N4 and ZrO2, which also causes more smearing on the ceramic and adhesion of wear debris to the SiC-bonded PCD ball for Al2O3 and AlN. Under lubricants, the COFs and the adhesion of wear debris are effectively reduced, and the wear rate of the ceramic is increased. There is little difference between deionized (DI) water and nanofluids on the effect of lubricants on COF for Al2O3 and AlN. However, for ceramics with higher fracture toughness, the nanofluids can reduce the COFs of Si3N4 and ZrO2 in comparison with DI water.

Reciprocating Friction and Wear Behavior of Reaction-Formed SiC Ceramic Against Bearing Steel Ball

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Friction and Wear Properties of Si3N4 and SiC Used for Water-Lubricated Sliding Bearings

Friction and Wear of Self-Mated SiC and Si 3 N 4 in Green Water-Based Lubricant

Analysis on Wear Properties and Impact Factors for Si3N4 Ceramic Mated with Chilled Cast Iron

The Research on Friction and Wear Properties of Silicon Carbide and Silicon Nitride

Effect of fiber orientation on tribological properties of fiber reinforced C/C‐SiC composites mated with ceramic ball

Tribological Behavior of Liquid Phase Sintered SiC Ceramics Under Dry Condition

Tribological behavior of aluminum matrix composites reinforced with ceramic particulates in dry sliding against a semimetallic friction material

Microstructure, Mechanical and Tribological Properties of CrSiC Coatings Sliding Against SiC and Al2O3 Balls in Water

In-situ friction and wear study of SiCα/SiCβ and Al2O3-TiC-Co composite ceramics

Investigation of Impact of C/Si Ratio on the Friction and Wear Behavior of Si/SiC Coatings Prepared on C/C-SiC Composites by Slurry Reaction Sintering and Chemical Vapor Infiltration

Friction and Wear of Si3N4 Ceramic/stainless Steel Sliding Contacts in Dry and Lubricated Conditions

A comparative study on tribological behavior of Al2O3, AlN, Si3N4 and ZrO2 ceramics sliding against polycrystalline diamond ball

Friction and wear properties of CrSiCN coatings with low carbon content as sliding against SiC and steel balls in water

Frictional performance of silicon carbide under different lubrication conditions

Friction and wear performance of CrSiBCN coatings sliding against ceramic and metal counterparts in sea water

Dry sliding tribological behavior of C/SiC under different load and speed

Wear Mechanism of Ceramic Microbeads As Grinding Media

Tribological Behavior of Chemically Bonded Ceramic Coatings Reinforced with Modified Carbon Fiber

Research on Tribology Property of Si-3N-4 Ceramic and Chilled Iron under Oil-Less Lubrication