Abstract:The constitutive behavior of AA7075 aluminum sheet like other metallic sheet materials is highly temperature and strain rate dependent at elevated temperatures. The uniaxial tensile test is commonly employed to characterize the temperature and strain rate dependent deformation behavior. However, the traditional uniaxial tensile testing and data analysis procedure treats the gauge length of sample as a uniformly-deforming (or homogeneous) region. This may not be accurate due to early localized deformation that is initiated in the gauge region at elevated temperatures. Treating the post-necking hardening behavior of uniaxial tensile samples has been an important task to expand the effective range of true stress-true strain curves at elevated temperatures for metal and alloys. To explore this issue, uniaxial tensile tests on AA7075-F sheets (with as-fabricated temper) were conducted at 673o K and four different test speeds. The test procedure also utilized an on-line 2-D digital image correlation (DIC) system method to obtain full-field strain map from the deforming gauge region of the test specimen. Local stress-strain curves at different points along the gauge length were then calculated based on the recorded local in-plane principal stress and strain values from macroscopic force data and current cross-section of the specimen at the chosen points. In this manner, the DIC strain analysis not only enabled the determination of stress-strain response but also the determination of strain rates at specific chosen points along the gauge length. The local stress-strain curves revealed significant deviation at an earlier stage of deformation from the global (or macroscopic) stress-strain response based on the entire gauge region. To estimate the constitutive behavior at different strain rates, a correction method to traditional stress-strain curves was applied to obtain a family of stress-strain curves at different constant strain rates based on the local stress-strain curves. Additionally, the material deformation response in the stress, strain and strain rate space in the 3D Cartesian coordinate system was also constructed for tests conducted at different stretching speeds. Further, a verification test was conducted to see if the above methodology could provide an accurate estimation of local deformation behavior of AA7075 sheet. Furthermore, the above experimental method was also coupled with the Gurson-Tvergarrd-Needleman (GTN) ductile void damage model and incorporated into ABAQUS-Explicit general purpose finite element (FE) analysis code via a VUMAT material subroutine. Good agreement was obtained for both the local and global stress-strain curves between the FE test simulation and experimental stress-strain results. The proposed experimental methodology and the resulting stress-strain-strain rate behavior is believed to be applicable in describing the strain rate-dependent constitutive behavior of AA7075-F sheet metals at 673o K.

Deformation Behavior in the Uniaxial Tension Process of Aluminum and Aluminum Alloy Sheets under Fluid Pressure

Research on aluminum alloy sheet thermoplastic deformation behavior based upon warm bulging test

Tensile and Compressive Deformation Behaviors of Commercially Pure Al Processed by Equal-Channel Angular Pressing with Different Dies

Deformation response research on aluminum sheets with different central pre-cracked defects under quasi-static hydraulic pressure loading

Effect of Strain State on the Surface Roughening for Hydroforming of Aluminum Alloy Tube Based on Cross-Scale Numerical Modeling

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet

Modeling of constitutive behavior and ductile fracture of AA5A06 aluminum alloy sheet in warm hydroforming process

Experimental and numerical investigation on plasticity and fracture behaviors of aluminum alloy 6061-T6 extrusions

Construction of 6061-T6 aluminum alloy constitutive model based on hot bulging test and study on the non-isothermal hydroforming process

Hot Deformation Behavior and Microstructure Evolution of High-Strength Al-Zn-Mg-Cu Alloy

Large strain flow curve identification for sheet metals under complex stress states

The Mechanism of Deformation Compatibility of TA2/Q345 Laminated Metal in Dynamic Testing with Split-Hopkinson Pressure Bar

Identification of forming performance parameters for 6016 aluminum alloy sheet under different strain paths via digital image correlation technology

Local and global tensile deformation behavior of AA7075 sheet material at 673oK and different strain rates

Study on hydroforming of AA6061-T6 aluminum alloy sheet based on upper sheet

Deformation Characteristics and Constitutive Equations for the Semi-Solid Isothermal Compression of Cold Radial Forged 6063 Aluminium Alloy

Microstructure, Fracture Mechanism, and Constitutive Analysis of Spray-Formed and Extruded Al-12Zn-2.4Mg-1.1Cu-0.3Zr Alloy

Enhanced deep drawing formability and deformation mechanism of aluminum alloy at cryogenic temperature

Anisotropic Mechanical Behavior and Microstructural Characteristics of AA2099-T83 Alloy Sheet: Experiment and Simulation

Investigation of the mechanisms on the abnormal features observed in thermal-mechanical testing of AA6061 under extrusion conditions

Modeling material behavior of AA5083 aluminum alloy sheet using biaxial tensile tests and its application in numerical simulation of deep drawing