Abstract:Porous NiTi lattice structures are widely used in the manufacture of crucial components owing to their excellent shape memory effect, superelasticity, and high damping capacities. However, the specific strength and lightweight characteristics of porous NiTi lattice structures fabricated by conventional technologies are limited by unpredictability. In this work, three types of porous NiTi structures based on triply periodic minimal surface (TPMS) – Diamond, Gyroid, and Primitive – were designed and manufactured by the laser powder bed fusion (LPBF) additive manufacturing process . This work demonstrates LPBF is a feasible and efficient approach to fabricate highly accurate porous NiTi TPMS structures. Moreover, the influence of each of these structures on the mechanical and shape memory properties was investigated. Among the three structures, Gyroid had the smallest volume fraction deviation. Furthermore, the Diamond structure had the largest compressive modulus (782.82 MPa) and ultimate yield strength (163.14 MPa). The Gyroid and Primitive structures exhibit excellent elastic recovery deriving from high values of compressive modulus (662.44 MPa, and 703.29 MPa), and can maintain reliable structural robustness. The Primitive structure exhibited the lowest mechanical properties (37.80 MPa). During the cyclic compression test, Gyroid and Primitive show a smaller unrecovered strain than Diamond. Primitive shows the largest recovered strain during the heating process (6.98%). The higher mechanical flexibility of Primitive structure endows this structure with higher recovery ratio. During the direct compression test, the residual strain exhibits a positive correlation with the loading strain. All three structures exhibit good deformation recovery capability with a strain of 4%. At a strain of 12%, recovered strain during heating became the dominant factor in the recovery of the TPMS structure. Overall, porous NiTi TPMS structures are capable of reversible compressibility composed of rapid elastic recovery and controllable shape memory recovery. The unique performance of porous NiTi TPMS structure fabricated by LPBF renders it a highly efficiency energy-absorbing structure.

High Damping Capacity in Porous Niti Alloy with Bimodal Pore Architecture

Microstructure and Properties of NiTi Foams with 69% Porosity

Tailoring the damping and mechanical properties of porous NiTi by a phase leaching process

Ti3Sn-NiTi Syntactic Foams with Extremely High Specific Strength and Damping Capacity Fabricated by Pressure Melt Infiltration.

Pore structures of high-porosity NiTi alloys made from elemental powders with NaCl temporary space-holders

High Porosity and High-Strength Porous NiTi Shape Memory Alloys with Controllable Pore Characteristics

Pore Formation Mechanism and Characterization of Porous NiTi Shape Memory Alloys Synthesized by Capsule-Free Hot Isostatic Pressing

High Damping of Lightweight TiNi-Ti 2 Ni Shape Memory Composites for Wide Temperature Range Usage

Effect of Nb on the Damping Property and Pseudoelasticity of a Porous Ni-Ti Shape Memory Alloy

Lightweight NiTi Shape Memory Alloy Based Composites with High Damping Capacity and High Strength

Enhanced Internal Friction and Specific Strength of Porous TiNi Shape Memory Alloy Composite by the Synergistic Effect of Pore and Ti2Ni

Preparation and characterization of porous NiTi alloys synthesized by microwave sintering using Mg space holder

Gradient Porosity and Large Pore Size NiTi Shape Memory Alloys

Superelastic Porous NiTi with Adjustable Porosities Synthesized by Powder Metallurgical Method

Porous NiTiNb alloys with superior strength and ductility induced by modulating eutectic microregion

High-strength porous NiTi shape memory alloys with stable cyclic recovery properties fabricated using elemental powders

Pore Control in Porous NiTi Alloy Produced by Combustion Synthesis Method with the Utilization of Space Holders

Mechanical and shape memory properties of NiTi triply periodic minimal surface structures fabricated by laser powder bed fusion

Effect of Pore Sizes on the Microstructure and Properties of the Biomedical Porous NiTi Alloys Prepared by Microwave Sintering

Space-holder engineered porous NiTi shape memory alloys with improved pore characteristics and mechanical properties

Preparation of High-Porosity Niti Alloys by Powder Sintering with Nacl Pre-Forming