Abstract:Porous NiTi lattice structures are widely used in the manufacture of crucial components owing to their excellent shape memory effect, superelasticity, and high damping capacities. However, the specific strength and lightweight characteristics of porous NiTi lattice structures fabricated by conventional technologies are limited by unpredictability. In this work, three types of porous NiTi structures based on triply periodic minimal surface (TPMS) – Diamond, Gyroid, and Primitive – were designed and manufactured by the laser powder bed fusion (LPBF) additive manufacturing process . This work demonstrates LPBF is a feasible and efficient approach to fabricate highly accurate porous NiTi TPMS structures. Moreover, the influence of each of these structures on the mechanical and shape memory properties was investigated. Among the three structures, Gyroid had the smallest volume fraction deviation. Furthermore, the Diamond structure had the largest compressive modulus (782.82 MPa) and ultimate yield strength (163.14 MPa). The Gyroid and Primitive structures exhibit excellent elastic recovery deriving from high values of compressive modulus (662.44 MPa, and 703.29 MPa), and can maintain reliable structural robustness. The Primitive structure exhibited the lowest mechanical properties (37.80 MPa). During the cyclic compression test, Gyroid and Primitive show a smaller unrecovered strain than Diamond. Primitive shows the largest recovered strain during the heating process (6.98%). The higher mechanical flexibility of Primitive structure endows this structure with higher recovery ratio. During the direct compression test, the residual strain exhibits a positive correlation with the loading strain. All three structures exhibit good deformation recovery capability with a strain of 4%. At a strain of 12%, recovered strain during heating became the dominant factor in the recovery of the TPMS structure. Overall, porous NiTi TPMS structures are capable of reversible compressibility composed of rapid elastic recovery and controllable shape memory recovery. The unique performance of porous NiTi TPMS structure fabricated by LPBF renders it a highly efficiency energy-absorbing structure.

Lightweight NiTi Shape Memory Alloy Based Composites with High Damping Capacity and High Strength

Fine-Grained Bulk NiTi Shape Memory Alloy Fabricated by Rapid Solidification Process and Its Mechanical Properties and Damping Performance

PREPARATION OF NANO-SIZED SiC REINFORCED NiTi SHAPE MEMORY COMPOSITES AND THEIR MECHANICAL PROPERTIES AND DAMPING BEHAVIOR

Fabrication of Integrated Ni-Ti Alloys Possessing Both Super-elastic and Shape Memory Properties by Laser Powder Bed Fusion

Preparation and characterization of porous NiTi alloys synthesized by microwave sintering using Mg space holder

Ti3Sn-NiTi Syntactic Foams with Extremely High Specific Strength and Damping Capacity Fabricated by Pressure Melt Infiltration.

Enhanced Internal Friction and Specific Strength of Porous TiNi Shape Memory Alloy Composite by the Synergistic Effect of Pore and Ti2Ni

High Damping Capacity in Porous Niti Alloy with Bimodal Pore Architecture

High Damping of Lightweight TiNi-Ti 2 Ni Shape Memory Composites for Wide Temperature Range Usage

Nb/Niti Laminate Composite with High Pseudoelastic Energy Dissipation Capacity

High Porosity and High-Strength Porous NiTi Shape Memory Alloys with Controllable Pore Characteristics

Volume Fraction Effect on the Mechanical and Shape Memory Properties of NiTi Gyroid Lattice Structure Fabricated by Laser Powder Bed Fusion

Study on the NiTi Shape Memory Alloys In-Situ Synthesized by Dual-Wire-feed Electron Beam Additive Manufacturing

High-strength porous NiTi shape memory alloys with stable cyclic recovery properties fabricated using elemental powders

Laser powder bed fusion additive manufacturing of NiTi shape memory alloys: A review

Endowing Low Fatigue for Elastocaloric Effect by Refined Hierarchical Microcomposite in Additive Manufactured NiTiCuCo Alloy

Mechanical and shape memory properties of NiTi triply periodic minimal surface structures fabricated by laser powder bed fusion

Microstructure Evolution and Functional Response of NiTi Shape Memory Alloy Manufactured by Dual-Wire Electron Beam Freeform Fabrication

Porous NiTiNb alloys with superior strength and ductility induced by modulating eutectic microregion

Gradient Porosity and Large Pore Size NiTi Shape Memory Alloys

Solidification characterization and its correlation with the mechanical properties and functional response of NiTi shape memory alloy manufactured by electron beam freeform fabrication