Abstract:The nature of the interface between ceramic particle (CP) and metal matrix is critical to obtain solidification microstructures with optimal mechanical properties of CP-reinforced Al alloys in additive manufacturing. Generally, when the lattice misfit between the CP (e.g., TiB 2 ) and the α-Al matrix is higher than 4%, the interfacial coherency reduces, lowering the effectiveness of CPs. Here, we demonstrate that an L1 2 three-dimensional compound (3DC), which possesses lattice misfit with α-Al lower than 1%, can be introduced in between TiB 2 and α-Al via properly regulating the solidification cooling rate. In the 5TiB 2 /Al-4.5Mg-0.7Sc-0.2Zr (wt.%) as a model system, the lattice coherence of the TiB 2 /α-Al interface is tailored by introducing a 10-30 nm thick Al 3 (Sc,Zr) 3DC interphase when the cooling rate is increased to ~1000 o C/s. But, further increasing the cooling rate to ~6800 o C/s, only Al 3 (Sc,Zr) two-dimensional compound (2DC) with an apparent lattice strain forms at the interface. Taking advantage of the cooling rate (10 2 -10 3 o C/s) provided by laser direct energy deposition (L-DED), the low-misfit "TiB 2 /Al 3 (Sc,Zr) 3DC/α-Al" multi-structural interfaces are acquired, enabling the 3.56TiB 2 /Al-4.36Mg-0.72Sc-0.22Zr alloy as fabricated with L-DED to achieved improved strength-ductility synergy (yield strength 257 MPa, elongation 13.8%) due to the isotropically fine Al grain structure and the homogenous TiB 2 particle dispersion. The outcome of this study provides fundamental knowledge on designing "ceramic/coherent primary interphase/metal matrix" multi-structural interfaces to improve the mechanical properties of engineering metallic materials manufactured by rapid solidification techniques, such as DED additive manufacturing (AM).

Synthesis Strategy of the Novel Ti–TiNi Laminate Metal Composite with Promising Damping Capacity and Elinvar Effect

Damping Behavior of 3d Woven Metallic Lattice Materials

Tailoring A Novel Network Reinforcement Architecture Exploiting Superior Tensile Properties of in Situ Tibw/Ti Composites

Fabrication of Integrated Ni-Ti Alloys Possessing Both Super-elastic and Shape Memory Properties by Laser Powder Bed Fusion

Fabrication and Property of W/Tininb Shape Memory Alloy Laminated Composite

Microstructure Characterization and Damping Behavior of the Novel Graphene Oxide/tini Laminate Composite Sheet

High damping capacity of AlSi10Mg-NiTi lattice structure interpenetrating phase composites prepared by additive manufacturing and pressureless infiltration

Design strategy of TiC reinforced heterogeneous Ti-composites with an induced slip system for achieving high strength-ductility

Dual-interfacial alloying mechanism in Ti-steel laminated metal composite fabricated by wire-arc directed energy deposition using a Cu-Ni interlayer

Simultaneous Improvement in Strength and Ductility of TC4 Matrix Composites Reinforced with Ti1400 Alloy and In Situ-Synthesized TiC

Extraordinary room temperature tensile ductility of laminated Ti/Al composite: Roles of anisotropy and strain rate sensitivity

Balancing the strength and ductility of Ti2AlC/TiAl composite with a bioinspired micro-nano laminated architecture

High damping performances over wide temperature range in the B doped Ti-Ni shape memory alloys

High damping and modulus of aluminum matrix composites reinforced with carbon nanotube skeleton inspired by diamond lattice

Endowing Low Fatigue for Elastocaloric Effect by Refined Hierarchical Microcomposite in Additive Manufactured NiTiCuCo Alloy

Achieving strength-ductility combination and anisotropy elimination in additively manufactured TiB/Ti6Al4V by in-situ synthesized network architecture with fine grains

Synergistic Strengthening Mechanisms of Dual-Phase (TiN+AlN) Reinforced Aluminum Matrix Composites Prepared by Laser Powder Bed Fusion

Superior strength-ductility combination in TiC/TC4 composites via In situ construction Ti 2 Cu nanoparticles

Heterogeneous network structures formed in TiC/TC4/β-Ti composites for enhancing both strength and ductility

Constructing dual-scale high-entropy alloy/polymer interpenetrating networks to develop a lightweight composite with high strength and excellent damping capacity

Nanoscale engineering of low-misfit TiB 2 /Al 3 (Sc,Zr)/α-Al multi-interface to improve strength-ductility synergy for direct energy deposited aluminum alloy