Abstract:Porous NiTi lattice structures are widely used in the manufacture of crucial components owing to their excellent shape memory effect, superelasticity, and high damping capacities. However, the specific strength and lightweight characteristics of porous NiTi lattice structures fabricated by conventional technologies are limited by unpredictability. In this work, three types of porous NiTi structures based on triply periodic minimal surface (TPMS) – Diamond, Gyroid, and Primitive – were designed and manufactured by the laser powder bed fusion (LPBF) additive manufacturing process . This work demonstrates LPBF is a feasible and efficient approach to fabricate highly accurate porous NiTi TPMS structures. Moreover, the influence of each of these structures on the mechanical and shape memory properties was investigated. Among the three structures, Gyroid had the smallest volume fraction deviation. Furthermore, the Diamond structure had the largest compressive modulus (782.82 MPa) and ultimate yield strength (163.14 MPa). The Gyroid and Primitive structures exhibit excellent elastic recovery deriving from high values of compressive modulus (662.44 MPa, and 703.29 MPa), and can maintain reliable structural robustness. The Primitive structure exhibited the lowest mechanical properties (37.80 MPa). During the cyclic compression test, Gyroid and Primitive show a smaller unrecovered strain than Diamond. Primitive shows the largest recovered strain during the heating process (6.98%). The higher mechanical flexibility of Primitive structure endows this structure with higher recovery ratio. During the direct compression test, the residual strain exhibits a positive correlation with the loading strain. All three structures exhibit good deformation recovery capability with a strain of 4%. At a strain of 12%, recovered strain during heating became the dominant factor in the recovery of the TPMS structure. Overall, porous NiTi TPMS structures are capable of reversible compressibility composed of rapid elastic recovery and controllable shape memory recovery. The unique performance of porous NiTi TPMS structure fabricated by LPBF renders it a highly efficiency energy-absorbing structure.

Ti3Sn-NiTi Syntactic Foams with Extremely High Specific Strength and Damping Capacity Fabricated by Pressure Melt Infiltration.

Highly Sensitive Large Strain Cellulose/multiwalled Carbon Nanotubes (mwcnts)/thermoplastic Polyurethane (TPU) Nanocomposite Foams: from Design to Performance Evaluation

Mechanical and shape memory properties of NiTi triply periodic minimal surface structures fabricated by laser powder bed fusion

Tailoring the damping and mechanical properties of porous NiTi by a phase leaching process

First Principles Studies on the Elastic, Thermodynamic Properties and Electronic Structure of Ti15−xMoxSn Compounds

Volume Fraction Effect on the Mechanical and Shape Memory Properties of NiTi Gyroid Lattice Structure Fabricated by Laser Powder Bed Fusion

Improvement of compressive property and damping capacity of multilayer aluminum matrix foams with 316 L hollow spheres and NiTi alloy sheets

Synthesis and Characterization of Ti-13Ta-6Sn Foams Produced Using Mechanical Alloying, the Space Holder Method and Plasma-Assisted Sintering

Synthesis Strategy of the Novel Ti–TiNi Laminate Metal Composite with Promising Damping Capacity and Elinvar Effect

Effect of Nb on the Damping Property and Pseudoelasticity of a Porous Ni-Ti Shape Memory Alloy

Mechanical Characterization of Superelastic NiTi Nanofoams by Molecular Dynamics Simulations

In-situ Synthesis of NiTi Shape Memory Alloys with Tunable Chemical Composition and Thermomechanical Response by Dual-Wire-feed Electron Beam Directed Energy Deposition

Effect of Ti content on the cell structure and compressive and energy absorption properties of Al 3 Ti/Al6061 foam composite

Constructing dual-scale high-entropy alloy/polymer interpenetrating networks to develop a lightweight composite with high strength and excellent damping capacity

Preparation and Compressive Performance of an A356 Matrix Syntactic Foam

Analysis of Microstructure Evolution and Mechanical Properties during Compression of Open-Cell Ni-Foams with Hollow Struts Using Micro-CT and FEM

High-strength porous NiTi shape memory alloys with stable cyclic recovery properties fabricated using elemental powders

Direct synthesis of ultralight, elastic, high-temperature insulation N-doped TiO2 ceramic nanofibrous sponges via conjugate electrospinning

Achieving Superelasticity in Additively Manufactured Ni-Lean NiTi by Crystallographic Design

Nanoporous amorphous carbon nanopillars with lightweight, ultrahigh strength, large fracture strain, and high damping capability

Effect of Structural Configurations on Mechanical and Shape Recovery Properties of NiTi Triply Periodic Minimal Surface Porous Structures