Abstract:In this study, equal channel angular pressing (ECAP) was applied to a hot-extruded Mg–5.00Zn–0.92Y–0.16Zr (wt.%) alloy to produce an ultrafine-grained a-Mg structure of 0.6μm with uniformly distributed fine quasicrystal Mg3YZn6 particles. The basal planes in the as-ECAPed alloy were inclined approximately 45° to the ECAP direction (EPD); thus, a high Schmid factor of 0.36 for (0001)〈112¯0〉 basal slip along EPD was obtained. Then, the superplastic behavior at low temperatures of 150–250°C and initial strain rates of 1.67×10−3s−1–1.67×10−1s−1 of the as-ECAPed alloy was investigated and compared with that of the as-extruded alloy. The microstructural development, texture evolution and cracking behavior during tensile tests were systemically investigated by electron backscattered diffraction (EBSD) analysis. During the tensile test along the EPD, the basal planes in the as-ECAPed alloy specimen were tilted approximately 15° away from the original position; thus, the basal planes were still in a position favorable for the basal slip along the EPD. As a result, a maximum elongation of 865% was obtained at 200°C and a strain rate of 1.67×10−3s−1, as a result of this favored basal texture and the excellent thermal stability of the ultrafine-grained structure. This optimum superplastic temperature of 200°C is much lower than that obtained for other Mg–Zn–Y–(Zr) alloys. In contrast, for the as-extruded alloy specimen, superplastic behavior did not occur until the critical condition of 250°C and a strain rate of 1.67×10−3s−1. Below this temperature and strain rate, the strong extrusion basal texture was maintained, and the cracks in the hot-worked coarse region (or un-DRXed region) were observed nucleating mainly associated with the formation of a 38° {101¯1}–{101¯2} double twin. At this temperature and strain rate, the hot-worked coarse regions were significantly refined by the dynamic recovery and the following recrystallization process. In the case, the formation of a double twin was prevented and the facture was delayed.

Effect of Heat Treatment on Internal Friction in ECAP Processed Commercial Pure Mg

Improved Mechanical Property and Internal Friction of Pure Mg Processed by ECAP

Internal Friction and Microplastic Deformation Behavior of Pure Magnesium Processed by Equal Channel Angular Pressing

Low-Frequency Damping Behavior of Pure Mg Processed by Equal Channel Angular Pressing

Effect of Grain Size on Cyclic Microplasticity of ECAP Processed Commercial Pure Magnesium

Effects Of Ecap And Annealing Treatment On The Microstructure And Mechanical Properties Of Mg-1y (Wt. %) Binary Alloy

Microstructure and tensile property of the ECAPed pure magnesium

Microstructure Evolution and Mechanical Behavior of Mg-10Gd-3Y-0.4Zr Alloy Processed by ECAP at High Temperature

The Microstructural Evolution and Superplastic Behavior at Low Temperatures of Mg–5.00Zn–0.92Y–0.16Zr (wt.%) Alloys after Hot Extrusion and ECAP Process

The microstructure and mechanical properties of Mg-Sn-based alloy processed by differential-thermal equal channel angular pressing

The improvement of grain refinement, texture modification and mechanical properties of pure Mg prepared by cyclic expansion extrusion with an asymmetric extrusion cavity

Effect of heat treatment on microstructure and mechanical properties of Mg-4Y-1.6Nd-1Sm-0.5Zr alloy

Influence of Texture on the Mechanical Properties of a Mg-6Al-1Zn-0.9Sn Alloy Processed by ECAP

Study on the Effect of the ECAP Deformation on the Organization and Properties of the Extruded Mg-Sn-Al Alloys

Microstructure and Mechanical Property of Pure Magnesium Processed by Cyclic Extrusion Compression

The Effects of Heat Treatment on the Response of WE43 Mg Alloy: Crystal Plasticity Finite Element Simulation and SEM-DIC Experiment

Microstructure Optimization of Mg-Alloys by the ECAP Process Including Numerical Simulation, SPD Treatments, Characterization, and Hydrogen Sorption Properties

Effect of Equal Channel Angular Extrusion on the Thermal Conductivity of an AX52 Magnesium Alloy

Microstructure and Mechanical Properties of Mg–Zn–Ca Alloy Processed by Equal Channel Angular Pressing

Processing maps of extruded AZ80 + 0.4% Ce magnesium alloy

Ductility enhancement in Mg–8.7Gd–4.18Y–0.42Zr magnesium alloy fabricated through extrusion and equal channel angular pressing (EX-ECAP)