Abstract:Although proton-conducting solid oxide fuel cells (PCFCs) is superior to traditional fuel cells,the two main challenges for restricting the experimental research and the commercialization of PCFCs application are its high manufacturing cost and difficulty in scale-up. In addition, the aqueous-based tape casting process as a novel strategy has been widely applied in fabricating thin, large-scale, cost-effective and environment-friendly electrolyte layer. In this paper, an 80 mm x 80 mm anode-supported proton-conducting solid oxide fuel cell is obtained through combining the multi-layer aqueous-based tape casting and co-sintering technology. The configuration of PCFCs is NiO-BaZr0.1Ce0.7Y0.1Yb0.1O3-delta (BZCYYb)/BZCYYb (similar to 12 mu m)/La0.6Sr0.4Co0.2Fe0.8O3-delta (LSCF)-BZCYYb. The performance of the cell with homogeneous microstructure reaches 389 mW cm(-2) at 800 degrees C in condition of 3% humidified hydrogen as fuel and normal air as oxidant. Combined with the successful experience of previous work, this work can provide theoretical and statistical accumulation and reference for future assembly of large-scale PCFCs.

Fabrication and Characterization of a Cathode-Support Solid Oxide Fuel Cell by Tape Casting and Lamination

A simple and easy one-step fabrication of thin BaZr0.1Ce0.7Y0.2O3−δ electrolyte membrane for solid oxide fuel cells

Scandia-stabilized Zirconia-Impregnated (la, Sr)MnO 3 Cathode for Tubular Solid Oxide Fuel Cells

Fabrication and Characterization of Ssz Tape Cast Electrolyte-Supported Solid Oxide Fuel Cells

Fabrication of Cathode Supported Solid Oxide Fuel Cell by Multi-Layer Tape Casting and Co-Firing Method

Optimization of the Solid Oxide Fuel Cell Anode by Tape Casting

Improvement of Anode-Supported Solid Oxide Fuel Cells

Novel Metal-Supported Solid Oxide Fuel Cells With Impregnated Symmetric La0.6sr0.4fe0.9sc0.1o3-Delta Electrodes

Development of Lsm-Based Cathodes for Solid Oxide Fuel Cells Based on Ysz Films

Preparation and Performance of Tri-layer Composite Anode Supported Fuel Cell

Performance Evaluation of Solid Oxide Fuel Cells with Thin Film Electrolyte Fabricated by Binder‐Assisted Slurry Casting

Fabrication and Optimization of La 0.4 Sr 0.6 Co 0.2 Fe 0.7 Nb 0.1 O 3- Δ Electrode for Symmetric Solid Oxide Fuel Cell with Zirconia Based Electrolyte

Fabrication and Characterization of Ni-SSZ/SSZ/LSM-SSZ Anode-Supported SOFCs by Tape Casting and Single-Step Co-Sintering Techniques

Fabrication and Electrochemical Characterization of Anode-Supported Microtubular Solid Oxide Fuel Cells Based on Ce0.8sm0.2o2-D Electrolytes

Metal-Supported Solid Oxide Fuel Cells with a Simple Structure

Infiltrated Porous YSZ As a Cathode Active Layer for Cathode-Supported Solid Oxide Fuel Cells

Fabrication and Study of LaNi0.6Fe0.4O3-δ and Sm0.5Sr0.5CoO3-δ Composite Cathode

Fabrication and Evaluation of a Ni/La0.75Sr0.25Cr0.5Fe0.5O3−δ Co-Impregnated Yttria-Stabilized Zirconia Anode for Single-Chamber Solid Oxide Fuel Cells

Fabrication and Performance of La0.6sr0.4co0.2fe0.8o3-Delta Infiltrated-Yttria-Stabilized Zirconia Cathode on Anode-Supported Solid Oxide Fuel Cell

Fabrication and Study of LaNi0.6Fe0.4O3-δ and Sm0.5Sr0.5CoO3-δ Composite Cathode for Proton-Conducting Solid Oxide Fuel Cells

Fabrication And Performance Of Anode-Supported Proton Conducting Solid Oxide Fuel Cells Based On Bazr0.1ce0.7y0.1yb0.1o3-Delta Electrolyte By Multi-Layer Aqueous-Based Co-Tape Casting