Abstract:Highly efficient hydrogen production from biomass can be realized by using catalysts in the reaction process under more mild hydrothermal conditions. Among various catalysts, Ni based catalysts are considered as the most promising catalyst for hydrogen production due to its low cost and good catalytic activity. In order to solve the problem of catalyst deactivation caused by carbon deposion at the acid site of Ni/Al2O3,the additives were studied to modify the Ni based catalysts loaded on Al2O3 in our research group. Cu, Co, Ce and Mg were chosed as additive and bimetal Ni-M or complex oxide catalysts were prepared by co-impregnation, impregnation by step, and co-precipitation, etc. The results show that the introduction of metal Ce can effectively improve the catalytic activity of hydrogen production, and the resistance of carbon deposition can also be improved, indicating that metal Ce is a suitable additive. Mg additive can restrain the formation of crystalline carbon on the surface of Ni-Al catalyst. Much lower heat-treating temperature or impregnation by step in preparation can obtain more effective active sites for Ni-Mg-Al catalyst. Moreover, Mg additive can improve the catalytic activity and hydrothermal stability of Ni-Al catalyst. As to the Ni catalyst loaded on rutile TiO2 prepared by sol-gel process, Ni crystals with much higher dispersity can be achieved by lowering the heat-treating temperature, which provide more active sites and promote the C-C bond breaking of biomass under hydrothermal conditions as well as water gas shift reaction and methanation reaction, thus improving the conversion efficiency of biomass. The thermodynamic analysis was performed with Aspen Plus V7.3.2. The thermodynamic models was built using the P-R equation of state and the MHV2 mixing rule to predict the gas yields in the hydrothermal gasification process. Hydrothermal gasification of biomass and its model compounds was theoretically analyzed. The equilibrium state of hydrothermal gasification reaction was obtained by calculating the gas production under certain temperature and pressure, which points out the direction and limitation of hydrothermal gasification reaction.

Hydrogen Production by the Catalytic Reforming of Volatile from Biomass Pyrolysis over a Bimetallic Catalyst

Hydrogen Production by Hydrothermal Gasification of Biomass：Catalysts and Thermodynamic Analysis

Hydrogen production from bio-oil model compounds dry (CO 2 ) reforming over Ni/Al 2 O 3 catalyst

Preparation of Hydrogen Through Catalytic Steam Reforming of Bio-oil

Hydrogen Production Via Catalytic Reforming of the Bio-Oil Model Compounds: Acetic Acid, Phenol and Hydroxyacetone

Hydrogen Production by Catalytic Reforming of Acetic Acid-Simulacrum of Pyrolysis Bio-Oil

Hydrogen Production by Catalytic Steam Reforming of Model Compounds of Biomass Fast Pyrolysis Oil

Steam Reforming of Model Compounds and Fast Pyrolysis Bio-Oil on Supported Nickle Metal Catalysts for Hydrogen Production

Steam Reforming of Biomass Tar for Hydrogen Production over NiO/ceramic Foam Catalyst

Hydrogen Production by Catalytic Steam Reforming of Model Compounds of Bio-Oil

Steam Reforming of Bio‐Oil for Hydrogen Production: Effect of Ni‐Co Bimetallic Catalysts

Effects of Preparation Method on the Performance of Ni/Al 2 O 3 Catalysts for Hydrogen Production by Bio-Oil Steam Reforming

Promoting Hydrogen-Rich Syngas Production from Catalytic Reforming of Biomass Pyrolysis Oil on Nanosized Nickel-Ceramic Catalysts

Hydrogen production by CO2 reforming of CH4 in coke oven gas over Ni–Co/MgAl2O4 catalysts

Hydrogen Production Via Steam Reforming of Acetic Acid over Biochar-Supported Nickel Catalysts

Hydrogen or synthesis gas production via the partial oxidation of methane over supported nickel–cobalt catalysts

Hydrogen Production from the Steam Reforming of Biogas over Ni-based Catalyst: the Role of Promoters and Supports

Hydrogen Production by Catalytic Steam Reforming of Heavy Components in Bio-Oil in Fluidized Bed Reactor

Hydrogen production by biomass gasification in supercritical water with bimetallic Ni-M/γAl2O3 catalysts (M = Cu, Co and Sn)

Catalytic reforming of polypropylene to produce hydrogen: Influence of support characteristics and active metal type in catalyst

Hydrogen Production by Catalytic Steam Reforming of Bio-Oil, Naphtha and Ch4 over C12a7-Mg Catalyst