Sensitive detection of carbon monoxide using a compact high power CW DFB-QCL based QEPAS sensor

Stefanski, P.,Lewicki, R.,Tarka, J.,Ma, Y.

DOI: https://doi.org/10.1364/cleo_at.2013.jw2a.68

2013-01-01

Abstract:Development of an ultra-sensitive, selective, and compact QEPAS-based CO sensor employing a high power CW DFB-QCL is reported. A minimum detectable concentration of 4ppbv was achieved for CO line (2169.2cm-1) using a 5sec data acquisition time.

What problem does this paper attempt to address?

Sensitive detection of CO and N2O using a high power CW 4.61 μm DFB-QCL based QEPAS sensor

Yufei Ma,Rafał Lewicki,Manijeh M. Razeghi,Xin Yu,Frank K. Tittel

DOI: https://doi.org/10.1364/cleo_at.2013.jw2a.80

2013-01-01

Abstract:A high power CW DFB-QCL based CO and N2O QEPAS sensor demonstrating the MDL of 1.5 ppbv and 23 ppbv, respectively was developed. Continuous monitoring of atmospheric CO and N2O concentration levels were performed. © OSA 2013.
High-Power DFB Diode Laser-Based CO-QEPAS Sensor: Optimization and Performance.

Yufei Ma,Yao Tong,Ying He,Xin Yu,Frank K. Tittel

DOI: https://doi.org/10.3390/s18010122

IF: 3.9

2018-01-01

Sensors

Abstract:A highly sensitive carbon monoxide (CO) trace gas sensor based on quartz-enhanced photoacoustic spectroscopy (QEPAS) was demonstrated. A high-power distributed feedback (DFB), continuous wave (CW) 2.33 μm diode laser with an 8.8 mW output power was used as the QEPAS excitation source. By optimizing the modulation depth and adding an optimum micro-resonator, compared to a bare quartz tuning fork (QTF), a 10-fold enhancement of the CO-QEPAS signal amplitude was achieved. When water vapor acting as a vibrational transfer catalyst was added to the target gas, the signal was further increased by a factor of ~7. A minimum detection limit (MDL) of 11.2 ppm and a calculated normalized noise equivalent absorption (NNEA) coefficient of 1.8 × 10−5 cm−1W/√Hz were obtained for the reported CO-QEPAS sensor.
Sensitive Detection of Carbon Monoxide Based on a QEPAS Sensor with a 2.3μm Fiber-Coupled Antimonide Diode Laser

Yufei Ma,Guang Yu,Jingbo Zhang,Xin Yu,Rui Sun

DOI: https://doi.org/10.1088/2040-8978/17/5/055401

IF: 2.1

2015-01-01

Journal of Optics

Abstract:In this paper, a sensitive quartz-enhanced photoacoustic spectroscopy (QEPAS)-based carbon monoxide (CO) sensor using a 2.3 mu m continuous wave (CW) distributed feedback (DFB) fibercoupled antimonide diode laser is demonstrated for the first time. Wavelength modulation spectroscopy and a second-harmonic detection technique are used to reduce the sensor background noise and simplify the data process. Water vapor is added into a 1000 ppm CO:N-2 gas mixture to improve the vibrational-translational relaxation rate of the analyzed CO for the purpose of enhancement of the QEPAS signal. After the modulation depth is optimized, a minimum detection limit of 43.3 ppm at the 4294.6 cm(-1) absorption line is achieved when the modulation depth is set to 0.32 cm(-1).
QEPAS Based Ppb-Level Detection of CO and N_2O Using a High Power CW DFB-QCL

Yufei Ma,Rafal Lewicki,Manijeh Razeghi,Frank K. Tittel

DOI: https://doi.org/10.1364/oe.21.001008

IF: 3.8

2013-01-01

Optics Express

Abstract:An ultra-sensitive and selective quartz-enhanced photoacoustic spectroscopy (QEPAS) sensor platform was demonstrated for detection of carbon monoxide (CO) and nitrous oxide (N2O). This sensor used a state-of-the art 4.61 μm high power, continuous wave (CW), distributed feedback quantum cascade laser (DFB-QCL) operating at 10°C as the excitation source. For the R(6) CO absorption line, located at 2169.2 cm(-1), a minimum detection limit (MDL) of 1.5 parts per billion by volume (ppbv) at atmospheric pressure was achieved with a 1 sec acquisition time and the addition of 2.6% water vapor concentration in the analyzed gas mixture. For the N2O detection, a MDL of 23 ppbv was obtained at an optimum gas pressure of 100 Torr and with the same water vapor content of 2.6%. In both cases the presence of water vapor increases the detected CO and N2O QEPAS signal levels as a result of enhancing the vibrational-translational relaxation rate of both target gases. Allan deviation analyses were performed to investigate the long term performance of the CO and N2O QEPAS sensor systems. For the optimum data acquisition time of 500 sec a MDL of 340 pptv and 4 ppbv was obtained for CO and N2O detection, respectively. To demonstrate reliable and robust operation of the QEPAS sensor a continuous monitoring of atmospheric CO and N2O concentration levels for a period of 5 hours were performed.
Compact and sensitive mid-infrared all-fiber quartz-enhanced photoacoustic spectroscopy sensor for carbon monoxide detection.

Yufei Ma,Yao Tong,Ying He,Xingang Jin,Frank K Tittel

DOI: https://doi.org/10.1364/OE.27.009302

IF: 3.8

2019-01-01

Optics Express

Abstract:A compact and sensitive quartz-enhanced photoacoustic spectroscopy (QEPAS) based sensor for carbon monoxide (CO) detection was demonstrated by using a mid-infrared all-fiber structure as well as a 3D-printed acoustic detection module. An all-fiber configuration has advantages of easier optical alignment, lower insertion loss improvement in system stability, reduction in sensor size and lower cost. The 3D-printed acoustic detection module was introduced to match the mid-infrared all-fiber structure and further decrease the sensor volume, which resulted in a small size of 3.5 cm(3) and a weight of 5 grams. A 2.33 mu m distributed feedback fiber-coupled diode laser was used as the laser excitation source. A custom quartz tuning fork (QTF) with a small-gap of 200 mu m was used as the acoustic wave transducer in order to improve the signal level of the QEPAS sensor. An acoustic micro resonator was utilized as the acoustic wave enhancer. The gas pressure and laser wavelength modulation depth were optimized, respectively. Water vapor was used to accelerate the vibrational-translational relaxation rate of the targeted CO molecule. Finally, a minimum detection limit (MDL) of 4.2 part per million (ppm) was achieved, corresponding to a normalized noise equivalent absorption (NNEA) coefficient of 7.4 x 10(-9) cm(-1) W/root Hz. An Allan deviation analysis was used to evaluate the long-term stability of the reported CO-QEPAS sensor system. With an integration time of 150 s, the MDL was improved to be 1.3 ppm. (C) 2019 Optical Society of America under the terms of the OSA Open Access Publishing Agreement
Research on High Sensitivity Detection of Carbon Monoxide Based on Quantum Cascade Laser and Quartz-Enhanced Photoacoustic Spectroscopy

Ma Yu-Fei,He Ying,Yu Xin,Yu Guang,Zhang Jing-Bo,Sun Rui

DOI: https://doi.org/10.7498/aps.65.060701

2016-01-01

Abstract:Quartz-enhanced photoacoustic spectroscopy (QEPAS) technology was invented lately. Therefore it is an innovative method for trace gas detection compared with other existing technologies. In this paper, trace gas detection for carbon monoxide (CO) based on QEPAS technology is demonstrated. In order to realize high sensitive detection, a novel mid-infrared, state-of-art 4.6 m high power, continuous wave (CW), distributed feedback (DFB) quantum cascade laser (QCL) with single mode output is used as the laser exciting source. Therefore, the strongest absorption of fundamental frequency band of CO is achieved. Using the wavelength modulation spectroscopy and the 2nd harmonic detection, the influence of laser wavelength modulation depth on QEPAS signal level is investigated. Two important parameters of Q-factor and resonant frequency for quartz tuning fork as a function of gas pressure are measured. After optimization of the modulation depth of laser wavelength, the gas pressure of CO:N2 gas mixture and the improving speed of the V-R relaxation rate through the addition of water vapor, a minimum detection limit (MDL) of 1.95 parts per billion by volume (ppbv) for CO at gas pressure of 500 Torr and modulation depth of 0.2 cm-1 is achieved with a 1 sec acquisition time and the addition of 2.6% water vapor in the analyzed gas mixture. Finally, the influence of level lifetime of the targeted gas on QEPAS signal amplitude is investigated by comparison of CO QEPAS sensor performance using two different CO absorption lines of R(5) and R(6) located at 2165.6 cm-1 and 2169.2 cm-1respectively. The expression of the QEPAS signal amplitude is modified by adding the level lifetime parameter for a better precision.
A Portable Gas Sensor for Sensitive CO Detection Based on Quartz-Enhanced Photoacoustic Spectroscopy

Ying He,Yufei Ma,Yao Tong,Xin Yu,Frank K. Tittel

DOI: https://doi.org/10.1016/j.optlastec.2019.02.030

IF: 4.939

2019-01-01

Optics & Laser Technology

Abstract:A compact, portable and rechargeable sensor platform based on quartz-enhanced photoacoustic spectroscopy (QEPAS) was demonstrated for the sensitive detection of carbon monoxide (CO). The acoustic detection module and the circuit components were both integrated which formed a sensor system with a weight of 3.2 kg and dimensions of 250 x 250 x 50 mm(3). Water vapor was added to the gas mixture in order to accelerate the vibration translation rate of CO molecules and improve the CO-QEPAS signal performance. An Allan deviation analysis was performed to assess the long-term performance of such a sensor system. For an integration time of 800 s, a minimum detection limit (MDL) of 21 ppb was obtained. To demonstrate the practical application of the reported compact and portable QEPAS sensor, a continuous measurement of CO from the combustion of three kinds of burning materials was performed.
Development a Low-Cost Carbon Monoxide Sensor Using Homemade CW-DFB QCL and Board-Level Electronics

Jingmin Dang,Haiye Yu,Chuantao Zheng,Lijun Wang,Yuanyuan Sui,Yiding Wang

DOI: https://doi.org/10.1016/j.optlastec.2017.10.037

2018-01-01

Abstract:A mid-infrared sensor was demonstrated for the detection of carbon monoxide (CO) at trace level. In order to reduce cost, a homemade continuous-wave mode distributed feedback quantum cascade laser (CW-DFB QCL), a mini gas cell with 1.6-m optical length, and some self-development electronic modules were adopted as excitation source, absorption pool, and signal controlling and processing tool, respectively. Wavelength modulation spectroscopy (WMS) and phase sensitive detection (PSD) techniques as well as wavelet filtering software algorithm were used to reduce the influence of light source fluctuation and system noise and to improve measurement precision and sensitivity. Under the selected P(11) absorption line located at 2099.083 cm(-1), a limit of detection (LoD) of 26 parts per billion by volume (ppbv) at atmospheric pressure was achieved with a 1-s acquisition time. Allan deviation was used to characterize the long-term performance of the CO sensor, and a measurement precision of similar to 3.4 ppbv was observed with an optimal integration time of similar to 114 s. As a field measurement, a continuous monitoring on indoor CO concentration for a period of 24 h was conducted, which verified the reliable and robust operation of the developed sensor. (C) 2017 Elsevier Ltd. All rights reserved.
A Sensitive Carbon Dioxide Sensor Based on Photoacoustic Spectroscopy with a Fixed Wavelength Quantum Cascade Laser

Shunda Qiao,Yanchen Qu,Yufei Ma,Ying He,Yao Wang,Yinqiu Hu,Xin Yu,Zhonghua Zhang,Frank K. Tittel

DOI: https://doi.org/10.3390/s19194187

IF: 3.9

2019-09-26

Sensors

Abstract:A photoacoustic spectroscopy (PAS) based carbon dioxide (CO2) sensor with a fixed wavelength quantum cascade laser (FW-QCL) was demonstrated. The emission wavelength of the FW-QCL at 4.42 μm in the mid-infrared spectral region matched a fundamental CO2 absorption line. Amplitude modulation of the laser intensity was used to match the resonant photoacoustic (PA) cell. The noise from the background was reduced with the correlation demodulation technique. The experimental results showed that the sensor had excellent signal stability and a concentration linear response. When the integration time was 1 s, a 1σ minimum detection limit (MDL) of 2.84 parts per million (ppm) for CO2 detection was achieved. The long-term stability of the sensor was evaluated by means of an Allan deviation analysis. With an integration time of ~100 s, the MDL was improved to 1 ppm. This sensor was also used to measure the CO2 concentration from some common emission sources, such as cigarette smoking, automobile exhaust, and the combustion of some carbon-containing materials, which confirmed the stability and robustness of the reported FW-QCL based CO2-PAS sensor system.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Mid-infrared Quasi-Distributed Carbon Monoxide Gas Sensing Based on QEPAS and Hollow Waveguide

Lei Qi,Weipeng Chen,Shunda Qiao,Jiachen Jiang,Yiwei Shi,Yufei Ma

DOI: https://doi.org/10.1016/j.infrared.2024.105653

IF: 2.997

2024-01-01

Infrared Physics & Technology

Abstract:In this paper, a mid-infrared quasi-distributed carbon monoxide (CO) gas sensing based on quartz-enhanced photoacoustic spectroscopy (QEPAS) and hollow waveguide (HWG) was proposed for the first time. Three micropores with a diameter of 200 μm were developed at three different locations of a HWG with a length of 30 cm. Three customized low-frequency quartz tuning forks (QTFs) with a resonant frequency of 8.7 kHz were used to detect the photoacoustic signals generated at the micropores to achieve quasi-distributed measurements of CO, which provides a new idea for monitoring the leakage of gas pipelines and so on. In order to improve the performance of the gas detection system, the strongest absorption line with CO located at 2179.77 cm−1 (4.58 µm) was selected as the target absorption line, and a quantum cascade laser (QCL) was used as the excitation source to achieve the detection of CO in the mid infrared spectral region. The experimental results show that all three QTFs have excellent concentration linear response to CO, and the minimum detection limit (MDL) of the three QTFs to CO were 2.40 ppm, 2.59 ppm, and 2.34 ppm, respectively. Finally, the experiment tested the response ability of three QTFs to different concentrations of CO at the same time. The results showed that for micropores with different concentrations, all three QTFs can detect their corresponding concentrations, which proves that the sensor can achieve quasi-distributed measurement.
A CO Trace Gas Detection System Based on Continuous Wave DFB-QCL

Jingmin Dang,Haiye Yu,Yujing Sun,Yiding Wang

DOI: https://doi.org/10.1016/j.infrared.2016.12.012

IF: 2.997

2016-01-01

Infrared Physics & Technology

Abstract:A compact and mobile system was demonstrated for the detection of carbon monoxide (CO) at trace level. This system adopted a high-power, continuous wave (CW), distributed feedback quantum cascade laser (DFB-QCL) operating at ∼22°C as excitation source. Wavelength modulation spectroscopy (WMS) as well as second harmonic detection was used to isolate complex, overlapping spectral absorption features typical of ambient pressures and to achieve excellent specificity and high detection sensitivity. For the selected P(11) absorption line of CO molecule, located at 2099.083cm−1, a limit of detection (LoD) of 26ppb by volume (ppbv) at atmospheric pressure was achieved with a 1s acquisition time. Allan deviation analysis was performed to investigate the long term performance of the CO detection system, and a measurement precision of 3.4ppbv was observed with an optimal integration time of approximate 114s, which verified the reliable and robust operation of the developed system.
Integrated near-infrared QEPAS sensor based on a 28 kHz quartz tuning fork for online monitoring of CO2 in the greenhouse

Yihua Liu,Haoyang Lin,Baiyang Antonio Zhou Montano,Wenguo Zhu,Yongchun Zhong,Ruifeng Kan,Bin Yuan,Jianhui Yu,Min Shao,Huadan Zheng

DOI: https://doi.org/10.1016/j.pacs.2022.100332

IF: 9.656

2022-01-27

Photoacoustics

Abstract:In this paper, a highly sensitive and integrated near-infrared CO2 sensor was developed based on quartz-enhanced photoacoustic spectroscopy (QEPAS). Unlike traditional QEPAS, a novel pilot line manufactured quartz tuning fork (QTF) with a resonance frequency f 0 of 28 kHz was employed as an acoustic wave transducer. A near-infrared DFB laser diode emitting at 2004 nm was employed as the excitation light source for CO2 detection. An integrated near-infrared QEPAS module was designed and manufactured. The QTF, acoustic micro resonator (AmR), gas cell, and laser fiber are integrated, resulting in a super compact acoustic detection module (ADM). Compared to a traditional 32 kHz QTF, the QEPAS signal amplitude increased by > 2 times by the integrated QEPAS module based on a 28 kHz QTF. At atmospheric pressure, a 5.4 ppm detection limit at a CO2 absorption line of 4991.25 cm-1 was achieved with an integration time of 1 s. The long-term performance and stability of the CO2 sensor system were investigated using Allan variance analysis. Finally, the minimum detection limit (MDL) was improved to 0.7 ppm when the integration time was 125 s. A portable CO2 sensor system based on QEPAS was developed for 24 h continuous monitoring of CO2 in the greenhouse located in Guangzhou city. The CO2 concentration variations were clearly observed during day and night. Photosynthesis and respiration plants can be further researched by the portable CO2 sensor system.
A Sensitive Carbon Monoxide Sensor Based on Photoacoustic Spectroscopy with a 2.3 μm Mid-Infrared High-Power Laser and Enhanced Gas Absorption

Shunda Qiao,Yufei Ma,Ying He,Xin Yu,Zhonghua Zhang,Frank K. Tittel

DOI: https://doi.org/10.3390/s19143202

IF: 3.9

2019-07-20

Sensors

Abstract:A photoacoustic spectroscopy (PAS)-based carbon monoxide (CO) gas sensor with a high-power laser and an enhanced gas absorption was demonstrated. The light source was a distributed feedback (DFB), continuous wave (CW) diode laser with a high output power of ~8 mW to give a strong excitation. The target gas received optical absorption enhanced two times by using a right-angle prism reflecting the laser beam. In order to reduce the noise from the background, wavelength modulation spectroscopy (WMS) and second-harmonic detection techniques were used. The modulation frequency and modulation depth were optimized theoretically and experimentally. Water vapor was added in the PAS sensor system to increase the vibrational–translational (V–T) relaxation rate of the CO molecule, which resulted in an ~8 times signal enhancement compared with the using of a dry CO/N2 gas mixture. The amplitude of the 2f signal had a 1.52-fold improvement compared to the one with only one time absorption. The experimental results showed that such a sensor had an excellent linear response to the optical power and gas concentration. At 1 s integration time, a minimum detection limit (MDL) for CO detection of 9.8 ppm was achieved. The long-term stability of the sensor system was evaluated with an Allan deviation analysis. When the integration time was 1100 s, the MDL improved to be 530 ppb. The detection performance of such a PAS-based CO sensor can be further improved when a laser with a higher output power and increasing optical absorption times is used.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
An Experimental and Theoretical Investigation of CO-QEPAS Sensor Based on a High Power DFB Diode Laser

Yao Tong,Yufei Ma,Ying He,Xin Yu

DOI: https://doi.org/10.1364/3d.2018.jm4a.17

2018-01-01

Abstract:A high sensitive CO-QEPAS sensor with a high power 2.33 μm diode laser was demonstrated. A 11.2 ppm detection limit was obtained and the pressure and temperature sensitivities of the reported sensor were analyzed.
A Sensitive Carbon Monoxide Sensor Based On Photoacoustic Spectroscopy With A 2.3 Mu M Mid-Infrared High-Power Laser And Enhanced Gas Absorption

Shunda Qiao,Yufei Ma,Ying He,Xin Yu,Zhonghua Zhang,Frank K. Tittel

DOI: https://doi.org/10.3390/s19143202

IF: 3.9

2019-01-01

Sensors

Abstract:A photoacoustic spectroscopy (PAS)-based carbon monoxide (CO) gas sensor with a high-power laser and an enhanced gas absorption was demonstrated. The light source was a distributed feedback (DFB), continuous wave (CW) diode laser with a high output power of similar to 8 mW to give a strong excitation. The target gas received optical absorption enhanced two times by using a right-angle prism reflecting the laser beam. In order to reduce the noise from the background, wavelength modulation spectroscopy (WMS) and second-harmonic detection techniques were used. The modulation frequency and modulation depth were optimized theoretically and experimentally. Water vapor was added in the PAS sensor system to increase the vibrational-translational (V-T) relaxation rate of the CO molecule, which resulted in an similar to 8 times signal enhancement compared with the using of a dry CO/N-2 gas mixture. The amplitude of the 2f signal had a 1.52-fold improvement compared to the one with only one time absorption. The experimental results showed that such a sensor had an excellent linear response to the optical power and gas concentration. At 1 s integration time, a minimum detection limit (MDL) for CO detection of 9.8 ppm was achieved. The long-term stability of the sensor system was evaluated with an Allan deviation analysis. When the integration time was 1100 s, the MDL improved to be 530 ppb. The detection performance of such a PAS-based CO sensor can be further improved when a laser with a higher output power and increasing optical absorption times is used.
Parts-per-billion detection of carbon monoxide: A comparison between quartz-enhanced photoacoustic and photothermal spectroscopy

Davide Pinto,Harald Moser,Johannes P Waclawek,Stefano Dello Russo,Pietro Patimisco,Vincenzo Spagnolo,Bernhard Lendl

DOI: https://doi.org/10.1016/j.pacs.2021.100244

IF: 9.656

2021-02-01

Photoacoustics

Abstract:We report on a comparison between two optical detection techniques, one based on a Quartz-Enhanced Photoacoustic Spectroscopy (QEPAS) detection module, where a quartz tuning fork is acoustically coupled with a pair of millimeter-sized resonator tubes; and the other one based on a Photothermal Spectroscopy (PTS) module where a Fabry-Perot interferometer acts as transducer to probe refractive index variations. When resonant optical absorption of modulated light occurs in a gas sample, QEPAS directly detects acoustic waves while PTS probes refractive index variations caused by local heating. Compact QEPAS and PTS detection modules were realized and integrated in a gas sensor system for detection of carbon monoxide (CO), targeting the fundamental band at 4.6 μm by using a distributed-feedback quantum cascade laser. Performance was compared and ultimate detection limits up to ∼ 6 part-per-billion (ppb) and ∼15 ppb were reached for QEPAS and the PTS module, respectively, using 100 s integration time and 40 mW of laser power.
Research on Detecting CO with Quartz Enhanced Photoacoustic Spectroscopy Based on 2.33 Μm Distributed Feed Back Laser

Hu Libing,Liu Kun,Wang Guishi,Wang Lei,Tan Tu,Gao Xiaoming

DOI: https://doi.org/10.3788/lop52.053002

2015-01-01

Laser & Optoelectronics Progress

Abstract:The novel 2.33 mm distributed feed back laser is used to detect carbon monoxide with off-beam quartz enhanced photoacoustic spectroscopy (QEPAS). The parameters including modulation frequency, modulation amplitude are optimized. The signal of off-beam QEPAS versus concentration of carbon monoxide is investigated. Good linearity between off-beam QEPAS signal and concentration of carbon monoxide is obtained. A normalized noise equivalent absorption coefficient of 3 × 10 cm·W/ Hz is obtained with a 1 s time constant of lockin amplifier.
Ppt Level Carbon Monoxide Detection Based on Light-Induced Thermoelastic Spectroscopy Exploring Custom Quartz Tuning Forks and a Mid-Infrared QCL.

Shunda Qiao,Yufei Ma,Ying He,Pietro Patimisco,Angelo Sampaolo,Vincenzo Spagnolo

DOI: https://doi.org/10.1364/oe.434128

IF: 3.8

2021-01-01

Optics Express

Abstract:In this paper, we report on an ultra-highly sensitive light-induced thermoelastic spectroscopy (LITES)-based carbon monoxide (CO) sensor exploiting custom quartz tuning forks (QTFs) as a photodetector, a multi-pass cell and a mid-infrared quantum cascade laser (QCL) for the first time. The QCL emitting at 4.58 µm with output power of 145 mW was employed as exciting source and the multi-pass cell was employed to increase the gas absorption pathlength. To reduce the noise level, wavelength modulation spectroscopy (WMS) and second harmonic demodulation techniques were exploited. Three QTFs including two custom QTFs (#1 and #2) with different geometries and a commercial standard QTF (#3) were tested as photodetector in the gas sensor. When the integration time of the system was set at 200 ms, minimum detection limits (MDLs) of 750 part-per-trillion (ppt), 4.6 part-per-billion (ppb) and 5.8 ppb were achieved employing QTF #1 #2, and #3, respectively. A full sensor calibration was achieved using the most sensitive QTF#1, demonstrating an excellent linear response with CO concentration.
Part-per-Billion (Ppb)-Level Acetylene Sensor Employing Optical Quartz Enhanced Photoacoustic Spectroscopy (QEPAS) with an Erbium-Doped Fiber Amplifier (EDFA) and a Fiber-Optic Fabry–Perot Interferometer

Cheng Lin,Xuelian Zhang,Xueyang Yan,Yan Cai,Wenjie Li

DOI: https://doi.org/10.1080/00032719.2024.2403020

2024-09-16

Analytical Letters

Abstract:An all-optical double-pass quartz enhanced photoacoustic spectroscopy (QEPAS) sensor for the detection of acetylene (C 2 H 2 ) at part-per-billion (ppb) levels was developed and experimentally validated. By employing an erbium-doped fiber amplifier (EDFA) capable of emitting up to 1 W of optical power, a commercial quartz tuning fork (QTF) resonating at 30.7 kHz, and double-pass acoustic microresonators, the amplitude of the QEPAS signal was significantly enhanced, thereby improving the sensitivity of the C 2 H 2 -QEPAS sensor. Instead of using piezoelectric detection in conventional QEPAS, a highly sensitive fiber-optic Fabry–Perot interferometer (FPI) was employed to measure the vibration of the QTF prong. A working point self-stabilizing technique was exploited to improve the demodulation sensitivity and stability. The linear response of the sensor to laser power and C 2 H 2 concentration confirmed that no saturation occurred. With an excitation laser power of 1 W and a C 2 H 2 absorption line of 1532.83 nm, a C 2 H 2 minimum detection limit (MDL) of 19.1 ppb was achieved, corresponding to a normalized noise equivalent absorption coefficient (NNEA) of 1.58 × 10 −8 cm −1 ∙W∙Hz −1/2 . Owing to its high sensitivity, long-term stability, and immunity to electromagnetic interferences, the QEPAS sensor provides considerable potential for remote gas sensing in environmental monitoring and other applications.

chemistry, analytical
HCN ppt-level detection based on a QEPAS sensor with amplified laser and a miniaturized 3D-printed photoacoustic detection channel.

Ying He,Yufei Ma,Yao Tong,Xin Yu,Frank K Tittel

DOI: https://doi.org/10.1364/OE.26.009666

IF: 3.8

2018-01-01

Optics Express

Abstract:Ultra-high sensitive and stable detection of hydrogen cyanide (HCN) based on a quartz-enhanced photoacoustic spectroscopy (QEPAS) sensor was realized using an erbium-doped fiber amplifier (EDFA) as well as a miniaturized 3D-printed photoacoustic detection channel (PADC) for the first time. A HCN molecule absorption line located at 6536.46 cm-1 was selected which was in the range of the EDFA emission spectrum. The detection sensitivity of the reported EDFA-QEPAS sensor was enhanced significantly due to the high available EDFA excitation laser power. A 3D printing technique was used to develop the compact PADC, resulting in a size of 29 × 15 × 8 mm3 and a mass of ~5 g in order to improve the sensor stability and implement sensor applications requiring a compact size and light weight. At atmospheric pressure, room temperature and a 1 s acquisition time, a minimum detection limit (MDL) of 29 parts per billion (ppb) was achieved, corresponding to a normalized noise equivalent absorption (NNEA) coefficient of 1.08 × 10-8 cm-1W/Hz-1/2. The long-term performance and the stability of the HCN EDFA-QEPAS sensor system were investigated using an Allan deviation analysis. It indicated that the MDL can be improved to 220 parts per trillion (ppt) with an integration time of 300 s, which demonstrated this compact, integrated and miniaturized 3D-printed PADC based sensor had an excellent stability.

Sensitive detection of carbon monoxide using a compact high power CW DFB-QCL based QEPAS sensor

Sensitive detection of CO and N2O using a high power CW 4.61 μm DFB-QCL based QEPAS sensor

High-Power DFB Diode Laser-Based CO-QEPAS Sensor: Optimization and Performance.

Sensitive Detection of Carbon Monoxide Based on a QEPAS Sensor with a 2.3μm Fiber-Coupled Antimonide Diode Laser

QEPAS Based Ppb-Level Detection of CO and N_2O Using a High Power CW DFB-QCL

Compact and sensitive mid-infrared all-fiber quartz-enhanced photoacoustic spectroscopy sensor for carbon monoxide detection.

Research on High Sensitivity Detection of Carbon Monoxide Based on Quantum Cascade Laser and Quartz-Enhanced Photoacoustic Spectroscopy

A Portable Gas Sensor for Sensitive CO Detection Based on Quartz-Enhanced Photoacoustic Spectroscopy

Development a Low-Cost Carbon Monoxide Sensor Using Homemade CW-DFB QCL and Board-Level Electronics

A Sensitive Carbon Dioxide Sensor Based on Photoacoustic Spectroscopy with a Fixed Wavelength Quantum Cascade Laser

Mid-infrared Quasi-Distributed Carbon Monoxide Gas Sensing Based on QEPAS and Hollow Waveguide

A CO Trace Gas Detection System Based on Continuous Wave DFB-QCL

Integrated near-infrared QEPAS sensor based on a 28 kHz quartz tuning fork for online monitoring of CO2 in the greenhouse

A Sensitive Carbon Monoxide Sensor Based on Photoacoustic Spectroscopy with a 2.3 μm Mid-Infrared High-Power Laser and Enhanced Gas Absorption

An Experimental and Theoretical Investigation of CO-QEPAS Sensor Based on a High Power DFB Diode Laser

A Sensitive Carbon Monoxide Sensor Based On Photoacoustic Spectroscopy With A 2.3 Mu M Mid-Infrared High-Power Laser And Enhanced Gas Absorption

Parts-per-billion detection of carbon monoxide: A comparison between quartz-enhanced photoacoustic and photothermal spectroscopy

Research on Detecting CO with Quartz Enhanced Photoacoustic Spectroscopy Based on 2.33 Μm Distributed Feed Back Laser

Ppt Level Carbon Monoxide Detection Based on Light-Induced Thermoelastic Spectroscopy Exploring Custom Quartz Tuning Forks and a Mid-Infrared QCL.

Part-per-Billion (Ppb)-Level Acetylene Sensor Employing Optical Quartz Enhanced Photoacoustic Spectroscopy (QEPAS) with an Erbium-Doped Fiber Amplifier (EDFA) and a Fiber-Optic Fabry–Perot Interferometer

HCN ppt-level detection based on a QEPAS sensor with amplified laser and a miniaturized 3D-printed photoacoustic detection channel.