Abstract:Silica fiber optic sensors are resistant to corrosive environments and high temperatures, making them attractive candidates for harsh conditions found in nuclear and aerospace industries. Moreover, fibers can be deployed remotely for continuous measuring of spatially distributed temperatures and strains. This study investigated embedding a Ni/Cu bi-metallic coated fiber in a stainless-steel 316 (SS316) matrix using laser powder bed fusion towards functionalizing metal components for site-specific health monitoring. The embedded fiber was continuously interrogated during controlled heating to 1000°C. The measured fiber strains were similar to the expected differential thermal strains between the fiber and the SS316 matrix, until divergent behavior was observed at temperatures >500°C. No debonding at the matrix–coating–fiber interfaces was observed during microscopy, but significant interactions between the coatings and matrix resulted in diffusion-driven chemistry variations and Kirkendall void formation. Applying the strain-lag theory revealed plastic behavior in the Ni coating at temperatures >500°C, limiting the strain transfer to the fiber at higher temperatures. It was estimated that the elastic modulus in the Ni coating had decreased from ~200 GPa at room temperature to below 40 GPa, starting at 600°C. The low elastic modulus above 600°C is within the margin of what the tangent modulus would be in the case of bilinear isotropic hardening. Regardless of the divergent strain transfer at higher temperatures, the fiber was exposed to the equivalent of 1.9% engineering strain at 1000°C, but measured only a 0.7% engineering strain due to the poor strain transfer. Although compensating for the plastic behavior of Ni proved challenging, the bonding of a brittle silica fiber to a metal matrix surviving to 1000°C invites potential iterations on coating material for future application. For example, the embedded fiber is sufficient for acoustic energy transfer, realizing high temperature distributed acoustic sensing.

Fabrication and Thermal Characteristics of Multilayer Metal-Coated Regenerated Grating Sensors for High-Temperature Sensing

Fabrication and thermal characteristics of Ti-Ag-Ni coated regenerated grating sensors for high-temperature sensing

Thermal Characteristics of Silver-Recoated Regenerated Grating Sensors for High-Temperature Sensing

Fabrication and Characterization of A Metal-Packaged Regenerated Fiber Bragg Grating Strain Sensor for Structural Integrity Monitoring of High-Temperature Components

Optical Fiber Sensor with Double Tubes for Accurate Strain and Temperature Measurement under High Temperature Up to 1000 °C

An Improved Metal-Packaged Strain Sensor Based on A Regenerated Fiber Bragg Grating in Hydrogen-Loaded Boron–Germanium Co-Doped Photosensitive Fiber for High-Temperature Applications

Development of Highly-Sensitive and Reliable Fiber Bragg Grating Temperature Sensors With Gradient Metallic Coatings for Cryogenic Temperature Applications

Optical Fiber Sensor and Assembly Method for Measuring the Tensile Strain of a Nickel-Based Directionally Solidified Superalloy in a High-Temperature Environment.

Fabrication of Microscale Heat-Resistant Grating for In-Situ High Temperature Deformation Measurement by Sampling Moiré Method

Highly-sensitive Fiber Bragg Grating Temperature Sensors with Metallic Coatings

Development of High-Temperature Wire-Grid Thin Film Strain Gauges

Fatigue Behavior of Metal-Packaged Regenerated Fiber Bragg Grating Strain Sensors at High Temperatures: A Preliminary Study

Temperature Sensing of Metal-Coated Fiber Bragg Grating

Multilayer Metal-Coated Fiber Bragg Grating for High-Temperature Sensing

Cascaded Fabry-Perot Interferometer-Regenerated Fiber Bragg Grating Structure for Temperature-Strain Measurement under Extreme Temperature Conditions.

Fabrication of Thermal-Resistant Gratings for High-Temperature Measurements Using Geometric Phase Analysis

Distributed Strain Sensing Using Bi-Metallic Coated Fiber Optic Sensors Embedded in Stainless Steel

A study of the temperature sensitivity of fiber Bragg gratings after metallization

Heat Treatment on Fiber Bragg Grating with Ni Coating for Elevated Temperature Sensor

Metal Coatings on Long-Period Fiber Gratings and the Implementation of an Associated Sensing Model

Highly Sensitive Ni-Cu Duplex Metal Coated Fiber Bragg Grating Temperature Sensor