Abstract:Purpose The purpose of this paper is to quantitatively investigate the effect of process parameters (including welding current, voltage and speed) and plate thickness on in-plane inherent deformations in typical fillet welded joint; meanwhile, the plastic strains remaining in the weld zone are also analyzed under different influencing factors. Design/methodology/approach To achieve the purpose of this study, a thermal-elastic-plastic finite element (TEP FE) model is developed to analyze the thermal-mechanical behavior of the T-welded joint during the welding process. Experimental measurements have verified the validity of the established TEP FE model. Using the effective model, a series of numerical experiments are performed to obtain the inherent deformations under the conditions of different influencing factors, and then the calculation results are discussed based on the relevant data obtained. Findings Through numerical simulation analysis, it is found that the longitudinal and transverse inherent deformations decrease with the increase of welding speed and plate thickness, whereas as the nominal heat input increases, the inherent deformations increase significantly. The longitudinal shrinkage presents a quasi-linear and nonlinear distribution in the middle and end of the weld, respectively. The plastic strains in the cross section of the T-joint also vary greatly because of the process parameters and plate thickness, but the maximum value always appears near the location of the welding toe, which means that this point faces a relatively large risk of fatigue cracking. The inherent deformations are closely related to the plastic strains remaining in the weld zone and are also affected by many influencing factors such as process parameters and plate thickness. Research limitations/implications In this study, relatively few influencing factors such as welding current, voltage, speed and plate thickness are considered to analyze the inherent deformations in the T-welded joint. Also, these influencing factors are all within a certain range of parameters, which shows that only limited applicability can be provided. In addition, only in-plane inherent deformations are considered in this study, without considering the other two out-of-plane components of inherent deformations. Originality/value This study can help to expand the understanding of the relationship between the inherent deformations and its influencing factors for a specific form of the welded joint, and can also provide basic data to supplement the inherent deformation database, thereby facilitating further researches on welding deformations for stiffened-panel structures in shipbuilding or steel bridges.

Experimental and computational analysis of residual buckling distortion of bead-on-plate welded joint

Research Of Weld On Axial Buckling Stress Of Multilayer Combined Cylindrical Shells

Effect of Post-Weld Heat Treatment on the Plastic Buckling of Welded Cylindrical Shells

Recent Research on Welding Distortion Prediction in Thin Plate Fabrication by Means of Elastic FE Computation

Effect of Welding Residual Stress on Plastic Buckling of Axially Compressed Cylindrical Shells with Patterned Welds

Analysis of Buckling Distortion Caused by Welding Using 3D Optical Measurement Technology

The Effect of Process Parameters and Plate Thickness on In-Plane Inherent Deformations in T-joint Fillet Weld

Effect of Local Geometric Imperfections on Axial Buckling of Welded Steel Tanks

Investigation of Inherent Deformation in Fillet Welded Thin Plate T-joints Based on Interactive Substructure and Inverse Analysis Method

Effect of welding on elephant foot buckling of large oil storage tank

AN FEM MODEL OF BUCKLING DISTORTION DURING WELDING OF THIN PLATE

Investigating Welding Distortion of Thin-Plate Stiffened Panel Steel Structures by Means of Thermal Elastic Plastic Finite Element Method

Welding Distortion and Inherent Deformation under Temporary Tacking and Its Released States

Welding Distortion Prediction In 5a06 Aluminum Alloy Complex Structure Via Inherent Strain Method

Evaluation Method for Inherent Deformation and its Application in Predicting Welding Distortion on Hull Blocks

Prediction of Welding Deformation and Residual Stress in A Multiply-Stiffened Plate

The Influence of Welding-Induced 3D Residual Stress and Distortion on the Ultimate Strength of Multi-Stiffened Thin Plate Structures under Cyclic Load

Study of Welding Inherent Deformations in Thin Plates Based on Finite Element Analysis Using Interactive Substructure Method

Comparative Study of Welding Deformation of a Stiffened Panel under Various Welding Procedures

Effect of Initial Deflection on Welding Induced Buckling Distortion of Stiffened Plate Structure

Numerical simulation on bucking distortion of aluminum alloy thin-plate weldment