Abstract:Since temperatures of airfoil surfaces in advanced turbine engines are approaching the limit of nickel base superalloys, Nb-Ti-Si base alloys as their potential materials have attracted much attention recently. Nb-Ti-Si base alloys have high melting temperature, suitable densities, good elevated temperature creep strength and acceptable room temperature fracture toughness, therefore, they are expected to be employed in the temperature range of 1200-1450 ℃ as structural materials. Alloying and directional solidification are generally used to obtain a better combination of room temperature fracture toughness with high temperature creep strength and oxidation resistance for an elevated-temperature alloy. In this paper, the master alloy ingot with a nominal composition of Nb20Ti-16Si-6Cr-5Hf-4Al-2B-0.06Y (atomic fraction, %) was prepared by using vacuum consumable arc-melting. The integrally directional solidification of this alloy was conducted in a high vacuum and ultrahigh temperature directional solidification furnace with the use of a ceramic crucible at melt temperature of 2050 ℃. The integrally directionally solidified microstructure, preferred orientation of constituent phases and solid/liquid (S/L) interface morphology at different solidifying rate (2.5, 5, 10,20, 50 and 100 μm/s) for this alloy have been investigated by XRD, SEM and EDS, and the growth mechanism of Nbss/(Nb, X)_5Si_3 (where Nbss denotes Nb solid solution, X represents Ti, Hf and Cr elements) eutectic in it has been discussed. The results show that the directionally solidified microstructure of the alloy is mainly composed of hexagonally cross-sectioned primary (Nb, X)_5Si_3 columns and coupled grown lamellar Nbss/(Nb, X)_5Si_3 eutectic colonies both aligned straight and uprightly along the growth direction. When the solidifying rate varies from 2.5 μm/s to 100 μm/s, the solid/liquid interface of the alloy undergoes an evolution from coarse cellular, fine cellular and finally to cellular dendrite morphologies. Both the average diameter of eutectic cells and lamellar spacing in them decrease with the increase in solidifying rate. The formation of a regular Nbss/(Nb, X)_5Si_3 eutectic morphology is attributable to a large kinetic undercooling and a low fusion entropies of alloy phases.

As-cast Microstructures and Solidification Paths of the Nb–Si–Ti Ternary Alloys in Nb5Si3–Ti5Si3 Region

Effect of B and Ti on the Directionally Solidified Microstructure of the Nb–Si Alloys

Liquid-solid phase equilibria in Nb-rich corner of the Nb-Ti-Si-B system

Experimental Study on the As-Cast Solidification of the Si-rich Alloys of the Nb–Si–Mo Ternary System

Experimental Investigation on the Phase Equilibria of the Nb-Ti-Si-B System at 1500 °C

Experimental Study on Phase Relationships in the Si-rich Portion of the Nb–Si–W Ternary System

Liquid-Solid Phase Equilibria of Nb-Si-Ti Ternary Alloys

Microstructures and mechanical properties of directionally solidified multi-element Nb-Si alloy

Phase Equilibria and Multi-Element Interaction Study in the Metal-Rich Side of the Nb–Ti–Si–Al Quaternary System

Effects of Alloying and High-Temperature Heat Treatment on the Microstructure of Nb–Ti–Si Based Ultrahigh Temperature Alloys

Experimental Investigation On The Phase Equilibria Of The Nb-Ti-Si-B System At 1500 A Degrees C

Effects of Ni, Co, B, and Ge on the microstructures and mechanical properties of Nb-Ti-Si ternary alloys

Effects Of Ti Content On Microstructure And Phase Compositions Of Nb-Si Based Ultrahigh Temperature Alloy

Effect of Ti Addition on Microstructure and Crystalline Orientations of Directionally Solidified Nb–Si Based Alloys

EFFECT OF SOLIDIFYING RATE ON INTEGRALLY DIRECTIONALLY SOLIDIFIED MICROSTRUCTURE AND SOLID/LIQUID INTERFACE MORPHOLOGY OF AN Nb-Ti-Si BASE ALLOY

Effect of Ti and Al Interaction on Microstructures and Mechanical Properties of the Nb-Ti-Si-Al Alloys

MICROSTRUCTURE AND SOLID/LIQUID INTERFACE MORPHOLOGY EVOLUTION OF INTEGRALLY DIRECTIONALLY SOLIDIFIED Nb-SILICIDE-BASED ULTRAHIGH TEMPERATURE ALLOY

Microstructure and Mechanical Properties of Nb/Nb5Si3 in Situ Composites in Nb–Mo–Si and Nb–W–Si Systems

Microstructure of Nb–Ti–Cr–Si Based Ultrahigh Temperature Alloy Processed by Integrally Directional Solidification

DIRECTIONALLY SOLIDIFIED MICROSTRUCTURE OF AN ULTRA-HIGH TEMPERATURE Nb-Si-Ti-Hf-Cr-Al ALLOY

Microstructure of the Nb-Si Based Multicomponent Alloy by Electromagnetic Cold Crucible Directional Solidifcation