Abstract:Since temperatures of airfoil surfaces in advanced turbine engines are approaching the limit of nickel base superalloys, Nb-Ti-Si base alloys as their potential materials have attracted much attention recently. Nb-Ti-Si base alloys have high melting temperature, suitable densities, good elevated temperature creep strength and acceptable room temperature fracture toughness, therefore, they are expected to be employed in the temperature range of 1200-1450 ℃ as structural materials. Alloying and directional solidification are generally used to obtain a better combination of room temperature fracture toughness with high temperature creep strength and oxidation resistance for an elevated-temperature alloy. In this paper, the master alloy ingot with a nominal composition of Nb20Ti-16Si-6Cr-5Hf-4Al-2B-0.06Y (atomic fraction, %) was prepared by using vacuum consumable arc-melting. The integrally directional solidification of this alloy was conducted in a high vacuum and ultrahigh temperature directional solidification furnace with the use of a ceramic crucible at melt temperature of 2050 ℃. The integrally directionally solidified microstructure, preferred orientation of constituent phases and solid/liquid (S/L) interface morphology at different solidifying rate (2.5, 5, 10,20, 50 and 100 μm/s) for this alloy have been investigated by XRD, SEM and EDS, and the growth mechanism of Nbss/(Nb, X)_5Si_3 (where Nbss denotes Nb solid solution, X represents Ti, Hf and Cr elements) eutectic in it has been discussed. The results show that the directionally solidified microstructure of the alloy is mainly composed of hexagonally cross-sectioned primary (Nb, X)_5Si_3 columns and coupled grown lamellar Nbss/(Nb, X)_5Si_3 eutectic colonies both aligned straight and uprightly along the growth direction. When the solidifying rate varies from 2.5 μm/s to 100 μm/s, the solid/liquid interface of the alloy undergoes an evolution from coarse cellular, fine cellular and finally to cellular dendrite morphologies. Both the average diameter of eutectic cells and lamellar spacing in them decrease with the increase in solidifying rate. The formation of a regular Nbss/(Nb, X)_5Si_3 eutectic morphology is attributable to a large kinetic undercooling and a low fusion entropies of alloy phases.

Liquid-solid phase equilibria in Nb-rich corner of the Nb-Ti-Si-B system

Experimental Investigation on the Phase Equilibria of the Nb-Ti-Si-B System at 1500 °C

Experimental Investigation On The Phase Equilibria Of The Nb-Ti-Si-B System At 1500 A Degrees C

Effect of B and Ti on the Directionally Solidified Microstructure of the Nb–Si Alloys

Thermodynamic Modeling of the Nb-rich Corner in the Nb–Si–Sn System

Phase Equilibria and Multi-Element Interaction Study in the Metal-Rich Side of the Nb–Ti–Si–Al Quaternary System

Liquid-Solid Phase Equilibria of Nb-Si-Ti Ternary Alloys

Effects of B and Si on the Fracture Toughness of the Nb–Si Alloys

Phase Equilibria in Nb-W-Rich Zone of the Nb-W-Si Ternary System

Effects of B on the Microstructure and Oxidation Resistance of Nb-Ti-Si-based Ultrahigh-temperature Alloy

Effects of Ni, Co, B, and Ge on the microstructures and mechanical properties of Nb-Ti-Si ternary alloys

As-cast Microstructures and Solidification Paths of the Nb–Si–Ti Ternary Alloys in Nb5Si3–Ti5Si3 Region

Solidification processes of as-cast alloys and phase equilibria at 1300 C of the Nb-Si-V ternary system

MICROSTRUCTURE AND SOLID/LIQUID INTERFACE MORPHOLOGY EVOLUTION OF INTEGRALLY DIRECTIONALLY SOLIDIFIED Nb-SILICIDE-BASED ULTRAHIGH TEMPERATURE ALLOY

Effects of Alloying and High-Temperature Heat Treatment on the Microstructure of Nb–Ti–Si Based Ultrahigh Temperature Alloys

Solidification Processes of As-Cast Alloys and Phase Equilibria at 1 300 °C of the Nb–Si–V Ternary System

Microstructures and Properties of Nb–Si-based Alloys with B Addition

Experimental Study on Phase Relationships in the Si-rich Portion of the Nb–Si–W Ternary System

EFFECT OF SOLIDIFYING RATE ON INTEGRALLY DIRECTIONALLY SOLIDIFIED MICROSTRUCTURE AND SOLID/LIQUID INTERFACE MORPHOLOGY OF AN Nb-Ti-Si BASE ALLOY

Isothermal Section at 1000 °C of the Nb–Ti–Si System

Application of phase equilibrium analysis in prepartion of Nb-Si based ultra-high temperature alloys