Abstract:This study deals with the Nb–niobium silicide-based composites developed by the hot-pressing of Nb–Si–Ti ternary powder mixtures with a fixed Ti addition (6at.%) and Si content ranging from hypereutectic (11at.%) to near-eutectic compositions (18at.%). The effects of Si content, Ti addition and strain rates on the sample microstructural characterization, flexural strength, fracture toughness, quasi-static compressive deformation and failure processes were investigated. It was revealed that the volume fraction of silicides increased with increasing Si content, and most of the Ti atoms dissolved into the niobium silicides to form (Nb,Ti)5Si3 solid solutions instead of binary titanium silicides. The experimental evidence showed that a moderate improvement in the flexural strength, fracture toughness and compressive yield stress of the composites was achieved by the addition of Ti. Higher Si additions produced a much more remarkable enhancement in the compressive yield stress and bulk hardness, whereas both the flexural strength and fracture toughness decreased with increasing Si content owing to the existence of residual porosities in the samples. The composites showed remarkable superiority to the arc-melted Nb–Si alloys and monolithic niobium silicides in fracture toughness (8.3–13.0MPam vs. 4.5MPam), where the toughening effect was attributed mainly to crack bridging and crack deflection by the remaining ductile Nb phase. Moreover, quasi-static uniaxial compression tests at strain rates between 10–5 and 10–3s−1 indicated that the deformation behavior and failure processes were significantly affected by Si content and strain rates. The strain-rate-hardening behavior for all the strain rates was observed in the composite materials and the strain-rate sensitivity decreased with increasing Si content. At a lower strain rate, the composite materials with a hypoeutectic Si composition failed with a pseudoplastic response and at an angle of ∼45° off the compressive loading direction. However, in the case of higher strain rate and Si content, the brittle failure in the samples occurred through vertical splitting and spalling of fragments.

Effects of Ni, Co, B, and Ge on the microstructures and mechanical properties of Nb-Ti-Si ternary alloys

Effect of Co on microstructures and mechanical properties for Nb-Si based in-situ composites

Microstructural and mechanical characterization of Nb-based in situ composites from Nb–Si–Ti ternary system

Effect of Nb-Content on Mechanical Properties of (Ni<sub>47</sub>Ti<sub>44</sub>)<sub>100-x</sub>Nb<sub>x</sub> Shape Memory Alloys

Why do schizophrenic patients refuse to take their drugs?

On the Alloying and Properties of Tetragonal Nb5Si3 in Nb-Silicide Based Alloys

Microstructure, Phase Transformation and Mechanical Property of Nb-doped Ni–Mn–Ga Alloys

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

On the Microstructure and Properties of Nb-12Ti-18Si-6Ta-2.5W-1Hf (at.%) Silicide-Based Alloys with Ge and Sn Additions

[Shock in animal experiments. Some problems of the regulation of the pulmonary and general circulation].

MICROSTRUCTURAL CHARACTERISTICS AND MECHANICAL PROPERTIES OF A Nb/Nb5Si3 BASED COMPOSITE WITH AND WITHOUT DIRECTIONAL SOLIDIFICATION

A Study of the Effects of Hf and Sn on the Microstructure, Hardness and Oxidation of Nb-18Si Silicide-Based Alloys-RM(Nb)ICs with Ti Addition and Comparison with Refractory Complex Concentrated Alloys (RCCAs)

Effect of Nb addition on microstructure and mechanical properties of TiC/Ti-7.8Cr composites

Microstructures and Mechanical Properties of Cast Nb-Ti-Si-Zr Alloys

Effect of Trace Strontium Addition on Microstructure and Room Temperature Fracture Toughness of Nb-12Si-22Ti Alloys

Effects of the microstructure and minor elements on the fracture toughness of Nb-Si alloy

Effect of Nb Element on Microstructure and Mechanical Properties of (Co30Cr25Fe40Ni5)100−xNbx High-Entropy Alloys

Effect of Nb Addition on the Glass-Forming Ability, Soft-Magnetic Properties and Mechanical Properties of CoFeNiBSiNb Bulk Glassy Alloys

Influence of alloying element Nb on the γ′ phase structure and mechanical properties of Co–8.8Al–9.8W alloy

Influence of Nb Content on Martensitic Transformation and Mechanical Properties of Tinicunb Shape Memory Alloys

Atomic diffusion and microstructural evolution at the Nb/TiAl heterogenous interfaces during annealing at elevated temperatures