Abstract:In order to explore whether (Nb,W) co-alloying TiAl-based alloys with relatively higher W addition have better high-temperature tensile rupture property, Ti-44Al-4Nb-1 W-0.1B alloy is designed and prepared. Ti-44Al-8Nb-0.1B alloy and Ti-44Al-7.2Nb-0.2 W-0.1B alloy are also prepared for comparative study. The rupture property testing is carried out at 800 °C and different tensile stresses. The property data , macro/microstructure evolution, fracture surface, W content, crack failure behaviors are studied. The results show that the (Nb,W) co-alloying alloys have better rupture property than the pure Nb alloying alloy. For the (Nb,W) co-alloying alloys, the higher W contained Ti-44Al-4Nb-1 W-0.1B alloy has the better property under lower tensile stress, and the lower W contained Ti-44Al-7.2Nb-0.2 W-0.1B alloy has the better property under higher tensile stress. The relationships of rupture life t and stress σ for the three alloys are given. All the three alloys have a coupling fracture mode of ductile fracture and brittle fracture. The ductile fracture exhibits the typical dimple characteristics. The brittle fracture exhibits the typical trans-granular cleavage, river-like pattern and trans-lamella fracture characteristics. The higher the stress, the more brittle fracture characteristics there are. After rupture property testing, the (α 2 + γ) lamella colony sizes of the three alloys all decrease, indicating that DRX and grain boundary slip occur not only along (α 2 + γ) lamella colony boundary, but also inside it. The colony boundary regions have the stress concentration, where the B2 phase produces the better buffering and coordination, and as well as the dislocation tangles, DRX and grain boundary slip can be found by EBSD and TEM. EPMA results show that the more W added in the alloy, the more W content is in the (α 2 + γ) lamella matrix, which is beneficial for the rupture property. However, more W addition will also lead to the formation of more B2 phase in the initial as-cast microstructure. So that, under higher tensile stress, when the stress intensity factor K is higher, the crack failure is more likely to occur.

Influence of alloying element Nb on the γ′ phase structure and mechanical properties of Co–8.8Al–9.8W alloy

Microstructural Instability and Precipitation Behaviors of Intermetallic Phases in a Nb-Containing CoNi-Based Superalloy

Effect of Nb Element on Microstructure and Mechanical Properties of (Co30Cr25Fe40Ni5)100−xNbx High-Entropy Alloys

High-throughput exploration of alloying effects on the microstructural stability and properties of multi-component CoNi-base superalloys

Effect of Nb on microstructure and properties of AlCoCrFeNi2.1 high entropy alloy

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Effect of Co on microstructures and mechanical properties for Nb-Si based in-situ composites

Microstructure, Phase Transformation and Mechanical Property of Nb-doped Ni–Mn–Ga Alloys

Theoretical Exploration of Alloying Effects on Stabilities and Mechanical Properties of γʹ Phase in Novel Co–Al–Nb-Base Superalloys

Microstructures and Mechanical Properties of a L12-structured Precipitation Strengthened Co-based Superalloy

Effects of Doped Elements (Si, Cr, W and Nb) on the Stability, Mechanical Properties and Electronic Structures of MoAlB Phase by the First-Principles Calculation

Enhancing structural stability of γ′-Co 3 (Al, Nb) phases: The key role of anti-site defects

Effect of Doping with Different Nb Contents on the Properties of CoCrFeNi High-Entropy Alloys

Effect of Nb content on the stacking fault energy, microstructure and mechanical properties of Fe-25Mn-9Al-8Ni-1C alloy

Effects of Niobium Addition on Dynamic Mechanical Behavior and Fracture Properties of Iron-Aluminide-Based Alloys

High-throughput investigation of Nb and Ta alloying effects on the microstructure and properties of a novel Ni-Co-based superalloy

Microstructure, Mechanical, and Tribological Properties of Nb-Doped TiAl Alloys Fabricated via Laser Metal Deposition

Atomistic investigation of effect of alloying on mechanical properties and microstructural evolution of ternary FeCo-X (X = V, Nb, Mo, W)

High-temperature tensile rupture property of (Nb,W) co-alloying TiAl-based alloys

Effect of substituting Mo for W on γ/γ′ partitioning behaviors of alloying elements in heat-treated second generation Ni based single crystal superalloys: An atom probe tomography study

Density functional theory study of the thermodynamic and elastic properties of Ni-based superalloys