Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Phase stability of Ti3SiC2 at high pressure and high temperature

Theoretical Investigation of the High Pressure Structure, Lattice Dynamics, Phase Transition, and Thermal Equation of State of Titanium Metal

Phase stability of SiC against Ti at high temperature

ChemInform Abstract: High Pressure in Situ Differential Thermal Analysis of Na0.5Bi0.5TiO3 Phase Transitions Up to 5 GPa.

Pressure-Induced Reversible Hcp to Fcc Phase Transition of Ti: A First-Principles Study

Helium-driven Element Depletion and Phase Transformation in Irradiated Ti3SiC2 at High Temperature

Evolution of Structural and Electronic Properties of TiSe2 under High Pressure

Elastic Stability of CO_{2} Phase I under High Temperature and Pressure

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Structure and Strength of SiC/Ti Bonding Interface.

The crystallographic stability and anisotropic compressibility of C54-type TiSi2 under high pressure

High pressure and high temperature in situ X-ray diffraction study on the structural stability of tantalum disilicide

High-temperature Microstructure Evolution and Thermal Stability of SiCf/Ti60 Composites

Theoretical analysis of Si3N4/TiC interfacial properties and material preparation

TiC phase in Ti alloys at different temperatures

Mechanical properties of polycrystalline Ti3SiC2 at ambient and elevated temperatures

Thermal Stability of SiCf/Ti60 Composites

Phase diagram of the Co-Cu-Ti system at 850°C

Pressureless manufacturing of high purity Ti3AlC2 MAX phase material: Synthesis and characterisation

The high-pressure phase transition of TiS2 from first-principles calculations

Phase reaction and diffusion path of the SiC/Ti system