Abstract:Industrial interest in wrought heat-treatable aluminium-lithium (Al–Li) based alloys dates back to around 1919 in Germany. However the exploitation of these alloys has historically been limited by their mechanical property anisotropy and concerns over their localized corrosion resistance and temperature stability. Recently, in the last ten years, alloy and process development has resulted in alloy compositions and thermomechanical treatments that potentially can overcome these issues. To put these developments in perspective we have reviewed the corrosion characteristics of first, second and third generation alloys with an emphasis on localized corrosion (intergranular and exfoliation) and stress corrosion cracking (SCC).Intergranular corrosion susceptibility of Al–Li–Cu and Al–Li–Cu–Mg alloys increases with copper content, and the depth of attack increases with ageing, i.e. UA<PA<OA. For alloys that contain zinc the mode of attack is less truly intergranular and more intra-granular or inter-subgranular in nature. Susceptibility to exfoliation corrosion has a similar temper dependence when assessed by conventional EXCO testing, but not following either exposure to a “real-life” outdoor marine environment or to a less aggressive test such as MASTMAASIS. In these tests there are two regimes of exfoliation susceptibility corresponding to under- and over-aged tempers, and an intermediate regime, including peak-aged tempers, with an improved resistance, i.e., UA>PA<OA.SCC initiation from smooth surfaces is rare for copper-free Al–Li alloys irrespective of temper or whether exposure is under continuous or alternate immersion conditions. For copper-containing alloys, initiation remains difficult for smooth specimens under continuous immersion conditions, but occurs readily under conditions of alternate immersion. It is likely that crack initiation is controlled by an anodic dissolution dominated process, but crack propagation may be controlled by either anodic dissolution or a hydrogen related process.Test results reviewed to date on thin plate samples show that the lower lithium content third generation Al–Li alloys, with suitable zinc and/or silver additions and thermomechanical processing can provide an acceptable resistance to localized corrosion (IGC and Exfoliation) and SCC in near to peak aged tempers. For this conclusion to apply to thicker products (>~30 mm) further analysis of corrosion test results is required.

General Aspects Related to the Corrosion of 6xxx Series Aluminium Alloys: Exploring the Influence of Mg/Si Ratio and Cu

Corrosion Mechanism of Mechanically Alloyed Mg50ni50 and Mg45cu5ni50 Alloys

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Microstructure Evolution and the Resulted Influence on Localized Corrosion in Al-Zn-Mg-Cu Alloy during Non-Isothermal Ageing

Interesting Phenomena for Al-Zn-Mg Aluminum Alloy after Two Years of Storage: A Comparative Study on Microstructure, Mechanical Properties and Corrosion Behavior of Aluminum Alloy with Different Aging Treatments

Computational and Experimental Insights into the Role of Acidic Molecules on the Corrosion Behavior on 7A46 Aluminum Alloy

Corrosion and Characterisation of Dual Phase Mg–Li–Ca Alloy in Hank’s Solution: the Influence of Microstructural Features

Study on properties and precipitation behavior of 6000 series alloys with high Mg/Si ratios and Cu contents

Effect of Aging Time on the Corrosion Behavior of a Cu-Ni-Si Alloy in 3.5 wt% NaCl Solution

Correlation of microstructure with corrosion performance in high zinc 7068 aluminum alloy aged using different T6 conditions

Corrosion and Stress Corrosion of Aluminum–Lithium Alloys

Localized corrosion characteristics of Al-Mg-Si aluminum alloy with aging time and pre-delayed aging condition

Formation of amorphous precipitates in a corroded over-aged Al-Mg-Si alloy

Effect of aging temperature on microstructure and corrosion behavior of 6082 aluminum alloy

Corrosion Behavior of Aluminum Alloys in Different Alkaline Environments: Effect of Alloying Elements and Anodization Treatments

Multi-scale study on the electrochemical behavior and corrosion mechanism of 5083 aluminum alloy with different microstructures in a NaCl environment

Influence of aging time on the corrosion behavior of 6061-T6 aluminum alloy in NaCl solution

Corrosion of magnesium alloys: the role of alloying

Corrosion Behavior of Extrusion, Under-Aged, Peaked-Aged and Over-Aged We93 Alloys in Nahso3 Solutions

Effect of Intermittent Variable Rate Non-isothermal Aging on the Corrosion Resistance of Al-Zn-Mg-Cu Alloy

Microstructure and corrosion behavior of as-homogenized and as-extruded Mg−xLi−3Al−2Zn−0.5Y alloys (x=4, 8, 12)