Abstract:Modified polypentafluorophenyl methacrylate with side‐groups of both POSS and alkane is prepared and blended with polypropylene through melt‐blending process. It is proved that this blend not only demonstrates durable hydrophobicity and enhanced mechanical properties due to its surface segregation, orientation, and crosslinking, but also can maintain those properties under many extreme conditions. Durable functionalization on polypropylene (PP) surfaces is always a key problem to besolved. Coatings with low surface energy peel off easily especially under extreme conditions, owing to their weak adhesion. In this paper, side groups of both polyhedral oligomeric silsesquioxane (POSS) and alkane are grafted to polypentafluorophenyl methacrylate (PFP), and then PP blends with these side‐group modified PFP are obtained through a melt‐blending process. It is found that POSS can result in surface segregation and provide hydrophobicity in blends. Microfibers are formed because of the orientation effect during the tensile testing, which furtherly promotes mechanical strength. Significantly, alkaneside‐groups can be entangled with PP segments, which brings about cross linking. Therefore, with crosslinking and synchronous orientation of POSS, the elongation at the break of blends is greatly increased up to 974%. The final blend demonstrates quite durable hydrophobicity under many extreme conditions, such as repeated tape peeling, ultrasonic washing, strong friction, and soaking in strong acid (pH = 1), strong alkali (pH = 14) and alcohol. The heat and UV resistance of the blend are also obviously improved. This study will develop anovel and facile strategy to endow PP with durable hydrophobicity as well as greatly enhanced mechanical properties.

The Studies on the Mechanical and Thermodynamic Properties of Surface Fluorinated Polypropylene/Polypropylene Blends

The mechanical properties and thermal performances of polypropylene with a novel intumescent flame retardant

The nonisothermal crystallization kinetics of surface fluorinated polypropylene/polypropylene blend

Effects of reactive compatibilization on the morphological, thermal, mechanical, and rheological properties of intumescent flame-retardant polypropylene.

Isothermal crystallization of polypropylene/surface modified silica nanocomposites

Influence of Syndiotacticity and Annealing Temperature on the Double Melting Peak Behaviour of Syndiotactic Polypropylene

Polypropylene Blends with Durable Hydrophobicity and Enhanced Mechanical Properties Based on POSS and Alkane Modified Polypentafluorophenyl Methacrylate

Investigation of Crystallization, Morphology, and Mechanical Properties of Polypropylene/Polypropylene-Polyethylene Block Copolymer Blends

Study on physical and mechanical properties of PP/Syndiotactic 1, 2- polybutadiene blends

Improved melting strength of polypropylene by reactive compounding with ultrafine full-vulcanized polybutadiene rubber (UFBR) particles

Novel Method for Preparation of Polypropylene Blends with High Melt Strength by Reactive Compounding

The study of the chemical crosslinked and foamed PP/LDPE

Study of the Preparation and Dielectric Property of Pp/Sma/Pvdf Blend Material

Morphology and Mechanical Behavior of Isotactic Polypropylene (ipp)/syndiotactic Polypropylene (spp) Blends and Fibers

Crystallization behaviors of polypropylene and functional polypropylene

The Influence of Pressure-Induced-Flow Processing on the Morphology, Thermal and Mechanical Properties of Polypropylene Blends

Study on Melting Grafted Polypropylene with High Fluidity

Crystallization Behavior of the Blends of Isotactic Polypropylene and Ethylene-Propylene Blocky Copolymers

Effect of Wet Surface Treated Nano-Sio2 on Mechanical Properties of Polypropylene Composite

Thermo-Blending of Biobased Poly(propylene 2,5-furan dicarboxylate) and Poly(lactic acid) with Improved Mechanical Performance

Blends of Polypropylene and Syndiotactic 1,2-Polybutadiene: Morphology, Crystallization Behaviors and Mechanical Properties