Abstract:In some circumstances, hybrid polymer microfluidic chips composed of both elastic, gas-permeable polydimethylsiloxane (PDMS) and rigid plastics are needed. However, it is quite difficult to bond PDMS irreversibly to plastics such as polystyrene (PS). In this article, a facile method for irreversible bonding of PDMS to PS was proposed based on UV/O-3-assisted surface modification in combination of surface silanization. Firstly, a PS sheet was exposed to UV/O-3 to produce oxygen-containing polar moieties, such as hydroxyl and carboxylic acid, on its surface. Secondly, the UV/O-3 treated PS sheet was silanized with (3-aminopropyl)triethoxysilane (APTES) via the reaction between the oxygen-containing polar moieties on the PS surface and the molecules of APTES. Thirdly, the silanized-PS sheet and the PDMS substrate with micro channel network were treated with UV/O-3 again to generate silanol moieties on both surfaces. Finally, the UV/O-3 treated PDMS was immediately brought intimate contact with the UV/O-3 treated silanized-PS, and irreversible bonding of PDMS with PS occurred after putting the PDMS-PS complex at room temperature for 1 h through the condensation reaction between silanol moieties. Contact angle measurement, X-ray photoelectron spectroscopy, total reflection Fourier transformation infrared spectrometer were applied to characterize the surface chemistry of the PS during the UV/O-3 treatment and silanization. The hybrid PDMS-PS microfludic chips prepared with the established method can bear a gas pressure higher than 0.5 MPa and a water stream at a flow rate higher than 170 mu L/min (the test channels were 2.5 cm in the length, 50 mu m in the width, 200 mu m in the depth). A hybrid PDMS-PS microfluidic chip composed of gas-permeable PDMS substrate with channel network and excellently biocompatible PS cover sheet was fabricated for cell culture. The experimental results showed that HeLa cells cultured in the hybrid PDMS-PS microchip grew much better than those cultured in the full PS microchip, and slightly better than those in the full PDMS microchip.

Preparation of thermoswitchable micro capillary force valves inside polydimethylsiloxane microfluidic channels

Thermally On−Off Switching Membranes Prepared by Pore-Filling Poly(N-isopropylacrylamide) Hydrogels

Fabrication of Micro Pneumatic Valves with Double-Layer Elastic Poly(dimethylsiloxane) Membranes in Rigid Poly(methyl Methacrylate) Microfluidic Chips

On-chip integrated multi-thermo-actuated microvalves of poly(N-isopropylacrylamide) for microflow injection analysis

Autonomous capillary microfluidic devices with constant flow rate and temperature-controlled valving

Reasearch and fabrication of integrated pneumatic microvalves in polymer microfluidic chip

Thermal-Responsive Anisotropic Wetting Microstructures for Manipulation of Fluids in Microfluidics

Preparation of Normally Open Microvalves with Fluorinated Ethylene Propylene Membrane and Poly(methyl Methacrylate) Substrates

The Pdms Micro Valve Driven by Pzt Piezoelectric Actuator on the Silicon Wafer

Self-Actuated, Thermo-Responsive Hydrogel Valves for Lab on a Chip

An Approach for Irreversible Bonding of PDMS-PS Hybrid Microfluidic Chips at Room Temperature

A Simple-Fabricated Passive Microvalve Using Rapid Prototyping of Glass and PDMS(polydimethylsiloxane)

Fabrication of Embedded Microvalve on PMMA Microfluidic Devices through Surface Functionalization

In-Channel Responsive Surface Wettability for Reversible and Multiform Emulsion Droplet Preparation and Applications.

Thermally-actuated microfluidic membrane valve for point-of-care applications

Teflon-seated One-Lambda Microvalves for PDMS Chips

Experimental Characterization of Electrical Current Leakage in Poly(dimethylsiloxane) Microfluidic Devices

A simple strategy for in situ fabrication of a smart hydrogel microvalve within microchannels for thermostatic control.

Preparation of hybrid soda-lime/quartz glass chips with wettability-patterned channels for manipulation of flow profiles in droplet-based analytical systems.

Thermoswitchable Electrokinetic Ion-Enrichment/Elution Based on a Poly(N-isopropylacrylamide) Hydrogel Plug in a Microchannel