Abstract:A 12% Cr ferritic/martensitic steel, HT-9, has been used as a primary core material for nuclear reactors. The microstructure and mechanical properties of gas tungsten arc butt welded joints of HT-9 in as-welded, and as-tempered conditions have been explored. In as-welded condition, the fusion zone (FZ) contained a fresh martensite matrix with delta (δ)-ferrite. The δ-ferrite was rich in Cr and depleted in C compared with the matrix. The heat-affected zone (HAZ) could be divided into three areas as the distance from the fusion line increased: δ-ferrite/martensite duplex zone, fully recrystallized zone, and partly recrystallized zone. Prior austenitic grains did not coarsen in the δ-ferrite/martensite duplex zone due to the newly nucleated δ-ferrite grains and incompletely ferritizing (δ-ferrite) during the welding thermal cycle. The weldment microhardness distributed heterogeneously with values above 600 HV1.0 in the HAZ and FZ and 250 HV1.0 in the base metal (BM). Solute C in the matrix, induced by the dissolution of carbide during the welding process, dominated the microhardness variation. Low toughness was observed in the FZ with a quasi-cleavage fracture tested from − 80 to 20 °C. The tensile fracture occurred in the relatively soft BM tested from 20 to 600 °C. In as-tempered condition (760 °C for 1 h), M23C6-type carbides precipitated within the martensitic laths, the lath boundaries, and the δ-ferrite/martensite interfaces. Moreover, V, Cr, Mo-rich nitrides with very small size also precipitated in the δ-ferrite/martensite interface. The tempering treatment improved the homogenous distribution of weldment hardness significantly. Tensile fracture still occurred in the BM of the weldment specimens tested from 20 to 600 °C. The impact toughness improved significantly, but the ductile–brittle transaction temperature was − 12 °C which was higher than that of the normalized and tempered (N&T) BM. δ-ferrite was considered to be one of the major factors aggravating the impact toughness in the FZ.

Heat Strength Evaluation and Microstructures Observation of the Welded Joints of One China-Made T91 Steel

DSI-based Studies of the Effects of High-temperature Aging on Local Mechanical Properties of HR3C/T92 Dissimilar Steel Welded Joint

Research Status and Advances of Manufacture and Properties of P91/T91 Steel in China

Carbon diffusion in dissimilar joints between P91 and 12Cr1MoV steels welded by different consumables at high temperature

Assessment of creep rupture properties for dissimilar steels welded joints between T92 and HR3C: CREEP PROPERTIES OF T92/HR3C WELDED JOINTS

Micro characteristics and macro performance of HR3C/T92 steel joints after 100000 hours service at high temperature

Microstructural and Performance Analysis of TP304H/T22 Dissimilar Steel Welded Joints

Investigation of Microstructures and Mechanical Properties of T92 Martensitic Steel/Super304 Austenitic Steel Weld Joints Made with Three Welding Consumables

Microstructure and Mechanical Characteristics of Dissimilar TIG Welded 9% Cr Heat-Resistant Steels Joints

Microstructure and mechanical properties of dissimilar materials joints between T92 martensitic and S304H austenitic steels

Analysis on the microstructure and properties of P92 steel after long-term service at high temperature

Deterioration of Mechanical Properties of Novel Constructional Steel Material at Elevated Temperatures

A Study of Microstructure and Mechanical Properties for the Autogenous Single-Pass Butt Weldment of a Ferritic/Martensitic Steel Using Gas Tungsten Arc Welding

Research on the creep damage and interfacial failure of dissimilar metal welded joint between 10Cr9Mo1VNbN and 12Cr1MoV steel

Microstructure and High-Temperature Properties Changes of P92 Welded Joints in Ultra-supercritical Units after Long-Term Service

Effect of Groove Design and Post-Weld Heat Treatment on Microstructure and Mechanical Properties of P91 Steel Weld

Research on the creep damage and interfacial failure of dissimilar metal welded joint between 10Cr9Mol VNbN and 12CrlMoV steel

Investigation of the High-Temperature Low-Cycle Fatigue Failure Characteristics of P91 Steel Weld Joints and their Fatigue Strength Reduction Factors under Various Load Control Regimes

Tailoring the Strength and Ductility of T91 Steel by Partial Tempering Treatment

Tempering process analysis and microstructure assessment of T91 steel

Effect of Surface Mechanical Attrition Treatment on Microstructure and Oxidation Behavior in T91 Steel at High Temperature