Abstract:Al-Zn-Mg-Cu alloy, as an important lightweight structural material in the aerospace field, has ushered in a broader application space and proposed higher performance requirements. This paper presents the experimental investigation of the effect of Zr content on the microstructure refinement and performance improvement of cast Al-5.8Zn-2.3Mg-1.7Cu alloy, aiming to optimize the additional amount of Zr, refine the alloy grains, and improve the microstructure uniformity and mechanical properties. The chemical component, phase, and microstructure were observed by inductively coupled plasma, X-ray diffraction, optical microscope and scanning electron microscope; the hardness and mechanical properties were measured by Brinell hardness tester and tensile testing machine. The addition of different contents of Zr into the alloy can form fine dispersed or primary coarse Al3Zr phase, which has a significant effect on the microstructure and mechanical properties of the alloy. The results indicate that the addition of 0.05 wt% Zr does not significantly improve the grain refinement and mechanical properties, but the Brinell hardness reaches the maximum. As the Zr content rises, the grain refinement effect becomes more obvious, while the mechanical properties first increase and then decrease. The addition amount reaches 0.20 wt%, the second dendrite arm spacing is the smallest, the ultimate tensile strength, yield strength and elongation at room temperature reach the maximum of 296.74 MPa, 249.41 MPa and 8.26%, respectively. When the amount of Zr added exceeds 0.20 wt%, the existence of coarse and brittle primary Al3Zr phase reduces the mechanical properties, and the fracture morphology changes from ductile to brittle intergranular fracture.

Ab initio study of the effect of Zr content on elastic and electronic properties of L12–Al3(Sc1−xZrx) alloys

Ab Initio Calculation of Structure and Thermodynamic Properties of Zintl Aluminide SrAl2

The first-principles calculations for the elastic properties of Zr2Al under compression

Effect of Zr, Hf, and Sn Additives on Elastic Properties of Α2-Ti3al Phase by First-Principles Calculations

The Structural, Elastic, and Electronic Properties of Zr X Nb 1− X C Alloys from First Principle Calculations

Effect of Zr addition on the microstructure evolution and mechanical properties of extruded Al-Cu-Li-Mn alloys

Influence of Zr content on microstructure and mechanical properties of As-cast Al-Zn-Mg-Cu alloy

Stability and physical properties tuning via interstitials chemical engineering of Zr5Sn3: a first-principles study

Effect of zr content on the microstructures and hydrogen storage properties of (Ti-Cr)(45-x)V55Zrx (x=1 similar to 7) alloys

Effects of Cr and Zr additions on the microstructure and properties of Cu-6wt.% Ag alloys

Lattice Stability and Elastic Properties of Zr-Ti-X Alloys (X = Al, V) by the First Principles Study

First-principles Study on the Structural Stabilities, Electronic and Elastic Properties of Zr2Si Alloy under Pressure

Theoretical investigations of Zr-concentration influence on the thermodynamic, elastic, electronic, and structural stability of D022/L12-Al3Ti

Effect of Zr addition on the local structure and mechanical properties of Ti–Ta–Nb–Zr refractory high-entropy alloys

Stability, Elastic and Electronic Properties of the Rh–Zr Compounds from First-Principles Calculations

Influences of different Zr/Sc ratios on microstructure and mechanical properties of Al-2Si alloy

Effect of scandium on microstructure and mechanical properties of high zinc concentration aluminum alloys

Distinct electron density topologies and elastic properties of two similar omega phases: ω-Zr and Zr2Al

Effect of Zr Microalloying on the Microstructures and Strengthening Mechanism of As-Cast Al-Fe-Zr Alloys

Effect of Sc contents on the mechanical properties and damping capacity of Al-Zn-Mg-Cu-Zr-Sc alloys with different grain structures

Influence of Sc and Zr additions on microstructure and properties evolution of Al–Zn–Mg alloy