Abstract:AbstractThe search for suitable friction materials for high-speed train is an attractive but difficult problem. In recent years, a variety of different novel friction materials were fabricated to meet the aims of high loads and speeds under ambient environment. Carbon fiber-reinforced carbon composites (C/C), carbon fiber-reinforced silicon carbide composites (C/C-SiC) and metallic composites fabricated by powder metallurgy are three excellent materials among them. Here a comparison of these three different materials working as brake pads, coupled with high-density C/C-SiC brake disk, was described. All the experiments were conducted using the same procedure with increasing initial braking speed (the rotation speed of brake disk at the beginning of braking process) from 30 to 59 m/s and constant load of 1.25 MPa, simulating the real working condition of high-speed train. The coefficient of friction (COF) and wear rates of three materials were compared and analyzed. During experiments, the COF of metallic and C/C pads remains nearly constant at 0.31 and 0.22, respectively, with increasing braking speed, while that of C/C-SiC exhibits a parabola. These different trends of COF may be attributed to the distinctive forming processes of friction film on the top of contact surfaces. Meanwhile, the wear rates of metallic composites increase rapidly from 683 to 1803 mm3/MJ with initial braking speed, while C/C-SiC presents the highest wear loss of 1887 mm3/MJ at 49 m/s and lowest value of 315 mm3/MJ at 59 m/s. Interestingly, the wear rate of C/C composites, due to the appropriate bonding strength of matrix/fiber and relatively high shear stress, decreases from 3698 to 903 mm3/MJ with increasing initial braking speed, which does not consist with pre-existing paper. Thus, metallic pads presented the lowest wear rates at lower speed (<49 m/s) but the highest at high speed, while C/C-SiC composite pads showed the greatest wear resistance at high speed. This investigation of three different friction materials will enhance our understanding of these friction materials and benefit the selection and safe application of high-speed train friction materials.

Friction and wear properties of C/C-SiC braking composites

Mechanical and tribological properties of C/C–SiC ceramic composites with different preforms

Wear Behaviour and Microstructural Changes of SiCw-Al Composite under Unlubricated Sliding Friction

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Microstructures and properties of C/C–SiC composites derived from different gaseous carbon matrix precursors

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

Friction and Wear Properties of Pitch/resin Densified Carbon Carbon Composites Used for Airbrakes

Friction and Wear Properties of Carbon/carbon Composites with Different Martix Carbon

Investigation of Impact of C/Si Ratio on the Friction and Wear Behavior of Si/SiC Coatings Prepared on C/C-SiC Composites by Slurry Reaction Sintering and Chemical Vapor Infiltration

Study on the Tribological Properties of Carbon Fabric/Polyimide Composites Filled with SiC Nanoparticles

In-situ friction and wear study of SiCα/SiCβ and Al2O3-TiC-Co composite ceramics

The Effect of Re-densification by Resin Impregnation on Frictional and Wear Properties of C/C Composites

The Microstructure and Wear Characteristics of Cu–Fe Matrix Friction Material with Addition of SiC

Comparison of Friction and Wear Behavior Between C/C, C/C-SiC and Metallic Composite Materials

Tribological behaviour of C/C–SiC composites—A review

Effect of fiber orientation on tribological properties of fiber reinforced C/C‐SiC composites mated with ceramic ball

Fabrication and Process Optimization of Chinese Fir-Derived SiC Ceramic with High-Performance Friction Properties

Dry sliding tribological behavior of C/SiC under different load and speed

The Effect of PyC/SiC Compound Interphase on the Properties of PIP SiC/SiC Composite

Microstructure, mechanical and friction-wear properties of SiC-WC composite with Al and C as sintering aids

Fading behavior and wear mechanisms of C/C–SiC brake disc during cyclic braking