Abstract:Squeeze casting process can effectively resolve the casting difficulties for wrought aluminum alloys by pressurized solidification. The effects of applied pressure (0.1-125 MPa) on the microstructure refinement, non-equilibrium eutectic phase aggregation and fracture behavior of Al-Zn-Mg-Cu alloys prepared by squeeze casting were investigated through metallography, scanning electron microscopy and energy dispersive spectroscopy. The results showed that the primary α-Al grains transformed from coarse dendrites to refined equiaxed grains with increasing pressure. Considerable primary refinement was achieved at 100 MPa, with a significant decrease by 63% in the average grain size from 273 μm to 101 μm; the non-equilibrium eutectic phases were homogenized and refined, and almost dissolved into the Al matrix after T6 heat treatment. The mechanism of solidification behaviors in pressurized solidification was elucidated. Firstly, the applied pressure increased the thermodynamic driving force to promote primary grain nucleation. Secondly, the solute diffusion and constitutional undercooling at the front of the solid/liquid interface front were inhibited by pressure, and grain growth in a dendritic structure was thus restrained. Thirdly, interdependence theory and thermodynamic calculations were conducted to quantitatively describe the primary grain size changes under pressurized solidification. Lastly, the ternary eutectic reaction L → α-Al + T-Mg (Al, Zn, Cu) 2 + Al 2 Cu and binary eutectic reaction L→ α-Al + Al 7 Cu 2 Fe were suppressed by the reduced solute segregation. Furthermore, when the pressure increased from 0.1 MPa to 125 MPa, the ultimate tensile strength was raised from 428 MPa to 538 MPa, almost approaching that of samples by forging process. The refined eutectic phases decreased stress concentration and improved fracture behaviors.

A quantitative model for describing crystal nucleation in pressurized solidification during squeeze casting

Microstructure simulation in pressurized solidification during squeeze casting of aluminum alloy A356

A Mathematical Model for Simulating the Microporosity of Squeeze Casting of Aluminum Alloy

A Thermomechanical Finite Element Model for Simulating the Solidification Process of Squeeze Casting

Thermomechanical Modeling of Solidification Process of Squeeze Casting Ii. Numerical Simulation and Experimental Validation

Thermomechanical Modeling of Solidification Process of Squeeze Casting I. Mathematic Model and Solution Methodology

Establishment of nucleation model and microstructure simulation of Al-Si alloy for low pressure die casting

Microstructure Simulation of Zl114a Alloy During Low Pressure Die Casting Process

Study on Dendritic Growth in Pressurized Solidification of Mg–Al Alloy Using Phase Field Simulation

Experiment and Numerical Simulation of Microstructure of ZL114A Alloy in Low Pressure Casting

AN ELASTIC-VISCOPLASTIC CONSTITUTIVE MODEL FOR SQUEEZE CASTING ALUMINUM ALLOY

Phase Field Simulation on Dendritic Growth in Pressurized Solidification of Mg-Al Alloy

Rapid Solidification of Non-Stoichiometric Intermetallic Compounds: Modeling and Experimental Verification

Effect of pressure on the microstructure refinement, solidification mechanism and fracture behavior of wrought Al-Zn-Mg-Cu alloys prepared by squeeze casting

Numerical Modeling of Microstructure Evolution and Dendrite Growth for Al-Si Alloy Casting During Low Pressure Die Casting

A Phase Field Model Coupled with Pressure-Effect-embedded Thermodynamic Modeling for Describing Microstructure and Microsegregation in Pressurized Solidification of a Ternary Magnesium Alloy

Study on the Relationship Between Interfacial Heat Transfer Coefficient and Interface Pressure in Squeeze Casting by Using Microscopic Contact Model

A quantitative study of solute diffusion field effects on heterogeneous nucleation and the grain size of alloys

The Challenge and Progress in Macro- and Micro-modeling and Simulation of Squeeze Casting Process

Study on Pressurized Solidification Behavior and Microstructure Characteristics of Squeeze Casting Magnesium Alloy AZ91D

Effects of Pressure on Homogeneous Nucleation and Growth during Isothermal Solidification in Pure Al: A Molecular Dynamics Simulation Study