Abstract:<p>The dispersion homogeneity of particles has a significant influence on the mechanical properties of particle reinforced metal matrix composites. In this study, a new Cu matrix composites with uniform dispersion of submicron and nanoscale MXene reinforcement particles were fabricated by the methods of high energy ball milling and hot pressing sintering. The microstructure evolution of MXene-Cu composite powders were studied in detail. When the initial MXene content is less than 3 vol%, the MXene particles can be dispersed homogenously in Cu matrix after 12 h ball milling. The refinement and dispersion of the MXene particles are mainly achieved by the cold welding and plastic deformation of composite particles in ball milling process. The XRD and TEM results reveal that these MXene reinforcement particles have been transformed to cubic TiC<sub>x</sub> in the final MXene/Cu composites. The tensile test results indicate that the UTS and elongation of the MXene/Cu composites are closely related to the dispersion homogeneity of the MXene particles. The UTS and elongation of the 1MXene/Cu and 3MXene/Cu composites increase with increasing the ball milling time. The UTS of the 3MXene/Cu-12 h can reach to 314 MPa with an elongation of 11.1%. The maximum UTS of the 5MXene/Cu-6 h can reach to 354 MPa. However, further increase in milling time would result in the UTS and elongation decline. The fracture surface analysis further testifies that the 3MXene/Cu-12 h composite presents a typical plastic fracture feature, while the 5MXene/Cu composite with various ball milling time all present brittle fracture characteristic for the severe agglomeration of MXene particles.</p>

Microstructures and Tensile Behavior of Carbon Nanotubes Reinforced Cu Matrix Composites with Molecular-Level Dispersion

Microstructure and Properties of In-Situ TiC Reinforced Copper Nanocomposites Fabricated Via Long-Term Ball Milling and Hot Pressing

Carbon-nanotube-templated Carbon Nanofibers with Improved Mechanical Performance

Enhancement of ultimate tensile strength and ductility of copper matrix composites using a low content of single-wall carbon nanotubes

Enhancement of mechanical properties and conductivity in carbon nanotubes (CNTs)/Cu matrix composite by surface and intratube decoration of CNTs

Optimization of the mechanical properties of CNTs/Cu composite by regulating the size of interfacial TiC

Improvement of interfacial interaction and mechanical properties in aluminum matrix composites reinforced with Cu-coated carbon nanotubes

Effects of the addition of CNTs and Al alloying on the microstructure and properties of Cu-(Al)/CNTs composites

[Familial infantile metachromatic leukodystrophy (Scholz-Greenfield disease). Sulfatide lipidoses].

Analysis of Load Transfer Mechanism in Cu Reinforced with Carbon Nanotubes Fabricated by Powder Metallurgy Route

Synergetic Effect of Graphene and MWCNTs on Microstructure and Mechanical Properties of Cu/Ti3SiC2/C Nanocomposites

Preparation, microstructure and tensile properties of two dimensional MXene reinforced copper matrix composites

Microstructure and Mechanical Properties of Cu-CoatedCarbon-Nanotubes-Reinforced Aluminum Matrix Composites Fabricated by Ultrasonic-Assisted Casting

Mechanical Properties of Cu-Based Composites Reinforced by Carbon Nanotubes

Investigation of Microstructure and Strengthening Mechanism in CNTs Reinforced Mo-based Composites

Study on the Mechanism of CNTs Regulating the Microstructures and Properties of Al–Cu–Mg Alloy

Enhancement mechanisms of mechanical, electrical and thermal properties of carbon nanotube-copper composites: A review

Achieving good strength‐plasticity compatibility in Cu composites via carbon nanotube (CNT)‐induced heterogeneous bimodal structure

The Microstructure and Mechanical Properties of Carbon Nanotube-Reinforced W-Matrix Composites

Toughening and strengthening of Cu-coated carbon nanotubes reinforced AZ61 magnesium matrix nanocomposites by improving interfacial bonding

CNT-induced heterogeneous matrix grain structure in CNTs/Al composites