Abstract:Two challenges for improving the performance of air cathode, single-chamber microbial fuel cells (MFCs) include increasing Coulombic efficiency (CE) and decreasing internal resistance. Nonbiodegradable glass fiber separators between the two electrodes were shown to increase power and CE, compared to cloth separators (J-cloth) that were degraded over time. MFC tests were conducted using glass fiber mats with thicknesses of 1.0 mm (GF1) or 0.4 mm (GF0.4), a Cation exchange membrane (CEM), and a J-cloth (JC), using reactors with different configurations. Higher power densities were obtained with either GF1 (46 +/- 4 W/m(3)) or JC (46 +/- 1 W/m(3)) in MFCs with a 2 cm electrode spacing, when the separator was placed against the cathode (S-configuration), rather than MFCs with GF0.4 (36 +/- 1 W/m(3)) or CEM (14 +/- 1 W/m(3)). Power was increased to 70 +/- 2 W/m(3) by placing the electrodes on either side of the GF1 separator (single separator electrode assembly, SSEA) and further to 150 +/- 6 W/m(3) using two sets of electrodes spaced 2 cm apart(double separator electrode assembly, DSEA). Reducing the DSEA electrode spacing to 0.3 cm increased power to 696 +/- 26 W/m(3) as a result of a decrease in the ohmic resistance from 5.9 to 2.2 Omega. The main advantages of a GF1 separator compared to JC were an improvement in the CE from 40% to 81% (S-configuration), compared to only 20-40% for JC under similar conditions, and the fact that GF1 was not biodegradable, The high CE for the GF1 separator was attributed to a low oxygen mass transfer coefficient (k(0) = 5.0 x 10(-5) cm/s).The GF1 and JC materials differed in the amount of biomass that accumulated on the separator and its biodegradability, which affected long-term power production and oxygen transport. These results show that materials and mass transfer properties of separators are important factors for improving power densities, CE, and long-term performance of MFCs.

Using cathode spacers to minimize reactor size in air cathode microbial fuel cells.

Optimization of catalyst dosage and total volume for extendible stacked microbial fuel cell reactors using spacer

Scalable air cathode microbial fuel cells using glass fiber separators, plastic mesh supporters, and graphite fiber brush anodes.

Increased Power Generation in a Continuous Flow MFC with Advective Flow Through the Porous Anode and Reduced Electrode Spacing

Air-cathode structure optimization in separator-coupled microbial fuel cells.

Microbial fuel cells with an integrated spacer and separate anode and cathode modules

Increasing Power Generation for Scaling Up Single-Chamber Air Cathode Microbial Fuel Cells.

Pressurized Air Cathodes for Enhanced Stability and Power Generation by Microbial Fuel Cells

The use of nylon and glass fiber filter separators with different pore sizes in air-cathode single-chamber microbial fuel cells

Power Generation by Packed-Bed Air-Cathode Microbial Fuel Cells

Scale-up of Membrane-Free Single-Chamber Microbial Fuel Cells

Scale-up and stack performance of single-chamber microbial fuel cells with activated carbon air cathodes

Evaluating a Multi-Panel Air Cathode Through Electrochemical and Biotic Tests

Enhancing sustainability and power generation from sewage‐driven air‐cathode microbial fuel cells through innovative anti‐biofouling spacer and biomass‐derived anode

Constructing Aerotolerant Bioanode with Flat and Compact Biofilm for High Power Generation of Microbial Fuel Cells

Unlaminated Carbon As Separator In Air-Cathode Single-Chamber Microbial Fuel Cells

Different Electrode Configurations to Optimize Performance of Multi-Electrode Microbial Fuel Cells for Generating Power or Treating Domestic Wastewater

Separator Characteristics for Increasing Performance of Microbial Fuel Cells

Tubular Membrane Cathodes for Scalable Power Generation in Microbial Fuel Cells.

Asymmetric Reactors As an Innovative Approach for Optimum Microbial Fuel Cells Performance

Increased sustainable electricity generation in up-flow air-cathode microbial fuel cells.