Abstract:This paper presents a RANS study of the hub clearance effects on the performance of a subsonic compressor stator. The inlet boundary conditions are from the calculation of inlet guide vanes. The k-ω SST turbulence model is adapted to resolve the Reynolds stresses. The present numerical results are compared with the experiment carried out at Technical University Berlin. The circumferentially averaged total pressure has a strong decrease in the lower span region from hub to nearly 50% channel height, while the tangential flow angle reduces from approximately 40% channel height to the hub, linearly. The above phenomenon indicates that the leakage flow in the gap between stator blade and the hub does not turn sufficiently. This leads to a smaller incidence angle of the flow to the stator, thus, the lower span of the stator works in smaller attack angle, 0 to 13 degrees lower than the higher span. Surface flow patterns on the hub and both side of the blade surfaces are compared with the oil flow visualization in the experiment. The compressor stator is shown to operate under large separation and strong back flow conditions. The hub leakage flow is studied together with the endwall flow phenomenon for full gap configuration. Two separation lines are observed on the hub. One is lying in front of the blade leading edge plane indicating the separation due to the leading edge leakage flow which spills out of the passage before the flow enters the passage. The other is caused by the interaction between the strong hub leakage flow and the incoming flow. This separation line undergoes an abrupt turning just after the flow leaving the stator passage. The effect of the hub gap size on the leakage flow and the whole flow passage in the stator, including the strength and location of the vortex structure, the location and size of the separation bubble, as well as the back flow behavior, is analyzed. With the help of a novel vortex identification method, the flow field of this subsonic compressor stator and the inlet guide vanes can be visualized illustrating the behavior at the operation point when rotating instability occurs. The parameter η4 can help identifying the stretching and relaxation of the vortex. This approach reveals significant flow details [1]. Combined with DPH (Dynamic Pressure Head) contour and streamlines, the detailed vortices structures and topology in a subsonic compressor can also be further elucidated. The study illustrates different vortices structures in the compressor, as well as their behavior in different gap size configurations.

Investigation of the Influence of Hub Gap Size to the Performance of A Subsonic Compressor Stator

Numerical Investigation of the Stator Hub Gap Effects on Aerodynamic Performance of a High-Pressure Compressor

NUMERICAL INVESTIGATION OF STATOR CLOCKING EFFECTS ON THE DOWNSTREAM STATOR IN A 1.5-STAGE AXIAL TURBINE

Experimental investigation of transient characteristics of mild surge and diffuser rotating stall in a centrifugal compressor with vaned diffuser

TRANSONIC COMPRESSOR DARMSTADT OPEN TEST CASE: EXPERIMENTAL INVESTIGATION OF STATOR SECONDARY FLOWS AND HUB LEAKAGE

Flow characteristics on a 4-stage low-speed research compressor with a cantilevered stator

Numerical investigation on the influence of nonuniform tip clearance on rotor tip-clearance flow field structure

Exploring the Aerodynamic Effect of Blade Gap Size via a Transient Simulation of a Four-Stage Turbine

The Influence of Rotor-Stator Spacing on the Loss in One-Stage Transonic Compressor

Detailed Simulations of a Three-Stage Supercritical Carbon Dioxide Axial Compressor with a Focus on the Shrouded Stator Cavities Flow

The Endwall Effects of Stators with and Without Simplified Penny Gaps in a High-Loaded Multistage Compressor

Characteristics of the axial compressor with different stator gaps in compressed air energy storage system

Numerical study of the coherent characteristics of the blade tip of a micro centrifugal compressor and its application in a new unsteady casing-treatment experiment

Study Of Shock/Blade Tip Leakage Vortex/Boundary Layer Interaction In A Transonic Rotor With Iddes Method

Numerical investigation of the unsteady tip leakage flow and rotating stall inception in a transonic compressor

Influence of Rotor-Stator Axial Clearance on Compressor Rotating Stall Characteristics

Investigation of the Instability Mechanisms in a Turbocharger Centrifugal Compressor with a Vaneless Diffuser by Means of Unsteady Simulations

Effects of Circumferentially Non-Uniform Clearance on the Spanwise Flow Characteristics in a Transonic Compressor Rotor

Numerical investigation of tip clearance effects on rotating instability of a low-speed compressor

Unsteady near-stall flow mechanisms in a transonic compressor rotor at different rotating speeds

Investigation of Positive Bowed Stator on Off-design Characteristics in a Multistage Compressor