Abstract:Fiber Bragg Gratings (FBG) have great significance in the development of high-power fiber laser systems. Fabrication sources, fibers, and fabrication technology would affect the performance of FBGs directly. In this research, a scanning exposure method for fabricating FBGs in different types of photosensitive fibers with a 213nm solid-state laser source was proposed. The Q-switched Nd: YVO4 laser fifth harmonic source was compared with the traditional excimer lasers and the impacts of lengths, center wavelengths, titled angles, and apodization on the reflection and transmission spectra of FBGs were discussed. The scanning fabrication system, which can realize the tilting of phase mask and the adjustment and monitoring of tension, was built according to the characteristics that the output spot diameter of the fabrication source was sub-millimeter. While the high quality of fabrication was guaranteed, FBGs with lengths of 3mm~20mm, center wavelengths shift of 0nm~4.2nm, and tilted angles of 0~21 were obtained, and all the parameters were simultaneously adjusted and controlled, the deepest transmission loss of about -70dB. FBGs fabricated were of good stability and repeatability, especially in hydrogen fibers whose stability was independent of high-temperature annealing (1500C) which was different from the fabrication results of excimer laser sources. Then the unconformity between experimental results and theoretical simulation was discussed and the optimization schemes were proposed. The experimental results and analysis provided a better experimental scheme for UV laser fabricating FBGs and the experimental basis for further optimizing the fabrication technology and further analyzing the microscopic mechanism of optical fiber photosensitivity.

Transient Bragg Fiber Gratings Formed by Unpumped Thulium Doped Fiber

Ultra-short Wavelength Operation in Thulium-doped Silica Fiber Laser with Bidirectional Pumping

Fabrication of fiber Bragg gratings with precisely adjustable and controllable parameters based on 213nm solid-state laser

Femtosecond Laser Inscription of Bragg Gratings in Tm3+-doped Fluorotellurite Glass Fibers for Lasing at 2.3 Μm

Optimized femtosecond laser direct-written fiber Bragg gratings with high reflectivity and low loss

High-Quality Fiber Bragg Gratings Inscribed by Femtosecond Laser Point-by-Point Technology

Fiber Bragg gratings fabricated by femtosecond lasers for narrow-linewidth fiber laser

Fiber Bragg gratings fabricated in fibers with different geometries by femtosecond laser written through the coating and their applications in strain sensing and fiber laser

Double-clad Tm3+-doped Silica Fiber Laser with Bragg Grating Inscribed Directly into Active Core by Femtosecond Laser

Bandwidth Characteristics of Fiber Bragg Grating Fabricated with Femtosecond Laser Radiation

Femtosecond Laser Inscribed Chirped Fiber Bragg Gratings.

High-efficiency continuous-wave Tm-doped fiber laser with a single fiber Bragg grating at 1942 nm

High Reflectivity, Ultraflat-Spectrum Chirped Fiber Bragg Grating Written Using Low Energy UV Femtosecond Pulses

Microcavity-coupled fiber Bragg grating with tunable reflection spectra and speed of light

A Single-Frequency Narrow-Linewidth Fiber Laser with PM Fiber Saturable Absorber

Tilted Fiber Bragg Grating Inscription in Boron Co-Doped Photosensitive Optical Fiber Using 266 nm Solid State Laser Pulses

Tunable Direct Writing of FBGs into a Non-Photosensitive Tm-Doped Fiber Core with an Fs Laser and Phase Mask

Silt-Beam Shaping Method for Femtosecond Laser Point-by-Point Inscription of Highly Localized Fiber Bragg Gratings with Enhanced Cladding Modes

Bragg Grating Inscription with Low Pulse Energy in Doped Microstructured Polymer Optical Fibers

A linear chirp fiber Bragg grating with tunable bandwidth enabled by MXene's photothermal effect

Fiber Bragg Grating with Enhanced Cladding Modes Inscribed by Femtosecond Laser and a Phase Mask