Abstract:A back-to-back reentrant cavity resonator (BTB RECR) in substrate integrated waveguide (SIW) configuration is integrated with a negative resistance oscillation (NRO) circuit to implement an SIW BTB RECR NRO-based active sensor for self-sustained sensing application. The dependence of sensitivity on the polarization between the dielectric sample and the induced E-field of the passive SIW BTB RECR is investigated to obtain sensitivity as high as possible. A multitask LabVIEW-based real-time test system, which can avoid disassembly and ensure the reliability of the measured results, is built up to selectively measure for transmission coefficient S $_{{21}}$ and frequency spectrum through a microwave switch. During the process of real-time replacement of deionized (DI) water reference solution with NaCl solution in dielectric sensing channel, the in-between real-time recorded oscillation frequency is cleverly used as the frequency-modulated (FM) input signal to the delay-line-based frequency demodulator and is transferred to in-phase V $_{{\text{I}}}$ and quadrature V $_{{\text{Q}}}$ dc voltages. Then, the modulated V $_{{\text{I}}}$ and V $_{{\text{Q}}}$ dc voltages are postprocessed into phase angle by using arctangent algorithm, and the phase angle in stable convergence state is finally used as response parameter for self-sustaining measurement for the concentration of NaCl solution. The NRO-based active sensor demonstrates a phase angle self-shift noise of 7.8 $^{\circ}$ and a high-resolution detection to NaCl solution at low concentration level from 2.5 to 80 mM/L and high concentration level from 100 to 800 mM/L. The measured minimum detectable lower limit concentration is 2.5 mM/L, and maximum sensitivity is 40 kHz/mM $\cdot$ L $^{{-1}}$ (0.31 $^{\circ}$ /mM $\cdot$ L $^{{-1}}$ ).

A Saw Oscillator Designed For Sensor Application

A Novel Serial High Frequency Surface Acoustic Wave Humidity Sensor

The Circuit Design of Portable SAW Vapor Sensors

Studies of a high-sensitive surface acoustic wave sensor for passive wireless blood pressure measurement

A K-Band CMOS Standing Wave Oscillator Using Digital-Controlled Artificial Dielectric Differential Transmission Lines

Low-phase-noise surface acoustic wave oscillator using phononic crystal bandgap-edge mode

Optical Waveguide Double-Ring Sensor Using Intensity Interrogation with a Low-Cost Broadband Source

Multilayered Surface Plasma Resonance Waveguide Sensing Device

A LOW POWER, LOW PHASE NOISE FBAR OSCILLATOR

Surface Acoustic Waves (SAW) Sensors: Tone-Burst Sensing for Lab-on-a-Chip Devices

High‐precision Dielectric Sensor System Based on Balanced CSRR‐SIW Resonators

Acoustic-optomechanical oscillator for low noise equivalent pressure and large broadband response acoustic sensing applications

Design Optimization of Surface Acoustic Wave Devices and Investigation of Fabricated Devices under Temperature, Humidity and Steam Environments

Highly-sensitive Optical Waveguide Sensor Based on SiON Using Two Cascaded-Microring Resonators

High-Performance SAWR Strain Sensor With Piston-Mode Operation

Selective Detection of CO 2 and H 2 O Dual Analytes Through Decoupling Surface Density and Shear Modulus Based on Single SAW Resonator

A multi-resolution passive SAW chemical sensor

Resonance Frequency Readout Circuit for a 900 MHz SAW Device.

Oscillation-Based Active Sensor on SIW Reentrant Cavity Resonator for Self-Sustained Ultralow Concentration Detection to Saline Solution

A 0.025mm(2) 0.8v 78.5db-Sndr Vco-Based Sensor Readout Circuit In A Hybrid Pll-Delta Sigma M Structure

A 0.025-Mm 2 0.8-V 78.5-Db SNDR VCO-Based Sensor Readout Circuit in a Hybrid PLL- $\delta\sigma$ M Structure