Abstract:Hollow fiber membranes fabricated via dry/wet phase inversion method usually have two dense skin layers,which will increase its resistance of mass transport as a support membrane. It is necessary that the dense skin layer of support membrane has been eliminated to improve separation performance of composite membrane. The excellent. chemical resistance of poly(vinylidene fluoride) (PVDF) to many acids and alkalis has made it as an attractive membrane material, and then it's often fabricated as porous hollow fiber membrane by phase inversion. In the process, the formation of the skin layer is due to the rapid exchange between solvent and coagulation, so many attempts have been made to slow it, so as to control the formation of the skin layer. In this paper, it has been found that the fabrication progress becomes unstable, and the membrane prepared has noncircular lumen, when the "weak" or "soft" coagulation is used. To increase the fabrication solution stability during membrane formation, dope viscosity was focused in this experiment. Dimethyl acetamide (DMAc) was used as solvent as well as internal coagulant, and the additives including LiCl, water and surfactant Span were chosen to investigate their effect oil the viscosity of the fabrication solution. The dope viscosity will greatly increase after adding LiCl, while the variety of dope viscosity is unconcerned in the fabrication solution concentration as adding water. The homogenization and stability of the fabrication solution are improved by adding Span,and the viscosity increases at the same time. Without increasing PVDF concentration, the stability of the nascent membrane was improved by increasing the fabrication viscosity. The PVDF hollow fiber membrane with the structure of single outer skin layer and finger-like pore through the cross-section, has been successfully fabricated. The mean pore radius and water flux of the single skin hollow fiber membrane were greatly improved.

Effects of Spinning Parameters on the Structure and Performance of PVC/PVVM Hollow Fiber Membrane

Effects of Preparing Condition on PVDF Membrane Morphology

Structure formation and characterization of PVDF hollow fiber membranes by melt-spinning and stretching method

Preparation and Structural Control of Polyethylene Hollow Fiber Membranes

Effect of Coagulation Bath Temperature on the Structure and Performance of Polyethersulfone Hollow Fiber Membranes by Dry/wet Process

Synthesis of PVC-b-PEG Copolymer and Its Modification Effect on PVC Microfiltration Membrane

Modification of Porous Poly(Vinylidene Fluoride) Membrane Using Amphiphilic Polymers with Different Structures in Phase Inversion Process

Influence of Dope Viscosity on the Fabrication of Pvdf Hollow Fiber Membranes with Single Skin Layer

Effect of Viscosity and Air Gap within the Spinneret on the Morphology and Mechanical Properties of Hollow-Fiber Polymer Membranes for Separation Performance

The Effects Of Pretreatment Condition Of Non-Woven Fabrics On The Pvc-Co-Pvac-Oh Membrane Performances

Dry–wet spinning of temperature-sensitive PVDF hollow-fiber membranes at different bore fluid flow rates

Effect of Polymer Molecular Weight on the Morphology and Crystallization of Prepared PVDF Membranes

INFLUENCE OF ALCOHOL-BASED NONSOLVENTS ON THE FORMATION AND MORPHOLOGY OF PVDF MEMBRANES IN PHASE INVERSION PROCESS

Experimental And Numerical Analyses On The Poly(Lactide-Co-Glycolide) Hollow Fiber Membranes

Effect of Dissolving Temperature of Dopes on the Morphology of PVDF Membrane

Effect of Additives on the Morphology and Performance of Symmetric Network PVDF Membranes

Progresses in the Modification and Application of Poly(vinyl Alcohol) Membrane

Effect of the molecular weight and its distribution of polyvinylidene fluoride on the relationship between the spinning process, microstructure and properties of hollow fiber membranes via thermally induced phase separation

Effect of Preparation Parameters on the Structure of PVDF Hollow Fiber Membranes

Effect of Maturation Time of Dopes on the Morphology and Crystallization of PVDF Membranes

Effect of Polymer Content on the Properties of PVDF Electro-spinning Nanofiber Membrane for Membrane Distillation