Abstract:A numerical investigation of the flow and heat transfer characteristics of tip leakage in a typical film cooled industrial gas turbine rotor is presented in this paper. The computations were performed on a rotating domain of a single blade with a clearance gap of 1.28% chord in an engine environment. This standard blade featured two coolant and two dust holes, in a cavity-type tip with a central rib. The computations were performed using CFX 5.6, which was validated for similar flow situations by Krishnababu et al. (2007, “Aero-Thermal Investigation of Tip Leakage Flow in Axial Flow Turbines: Part I—Effect of Tip Geometry,” ASME Paper No. 2007-GT-27954). These predictions were further verified by comparing the flow and heat transfer characteristics computed in the absence of coolant ejection with computations previously performed in the company (SIEMENS) using standard in-house codes. Turbulence was modeled using the shear-stress transport (SST) k-ω turbulence model. The comparison of calculations performed with and without coolant ejection has shown that the coolant flow partially blocks the tip gap, resulting in a reduction in the amount of mainstream leakage flow. The calculations identified that the main detrimental heat transfer issues were caused by impingement of the hot leakage flow onto the tip. Hence three different modifications (referred as Cases 1–3) were made to the standard blade tip in an attempt to reduce the tip gap exit mass flow and the associated impingement heat transfer. The improvements and limitations of the modified geometries, in terms of tip gap exit mass flow, total area of the tip affected by the hot flow and the total heat flux to the tip, are discussed. The main feature of the Case 1 geometry is the removal of the rib, and this modification was found to effectively reduce both the total area affected by the hot leakage flow and total heat flux to the tip, while maintaining the same leakage mass flow as the standard blade. Case 2 featured a rearrangement of the dust holes in the tip, which, in terms of aerothermal dynamics, proved to be marginally inferior to Case 1. Case 3, which essentially created a suction-side squealer geometry, was found to be inferior even to the standard cavity-tip blade. It was also found that the hot spots, which occur in the leading edge region of the standard tip, and all modifications contributed significantly to the area affected by the hot tip leakage flow and the total heat flux.

Aerothermal Investigation of Backface Clearance Flow in Deeply Scalloped Radial Turbines

Les and Cdns Investigation of T106c Low Pressure Turbine

Large Eddy Simulation and CDNS Investigation of T106C Low-Pressure Turbine

Investigation of clearance flows in deeply scalloped radial turbines

Investigation of backface cavity sealing flow in deeply scalloped radial turbines

Roughness Effects on Flow Losses of a High-Lift Low-Pressure Turbine Cascade

Numerical simulation of internal flow in forward-curved centrifugal fan

An Investigation of the Flow Structure in the Radial Inflow Transonic Turbine

Aerothermal Investigation of Tip Leakage Flow in a Film Cooled Industrial Turbine Rotor

Aero-Thermal Investigation of Tip Leakage Flow in a Film Cooled Industrial Turbine Rotor

Numerical Study on Flow and Heat Transfer Characteristics of Swirl Cooling on Leading Edge Model of Gas Turbine Blade

Numerical study of flow in low-pressure turbines with undulated suction surface

Contoured Endwall Flow And Heat Transfer Experiments With Combustor Coolant And Gap Leakage Flows For A Turbine Nozzle Guide Vane

Numerical investigations on leakage performance and flow mechanism of spiral groove seal for shrouded blade in axial turbine

Experimental and simulation study of energy loss mechanism of low pressure ratio radial turbine

Leakage Flow Mixing in Shrouded Axial Turbines and Its Control Strategies Using Casing Optimization

Clearance flow patterns and pressure distribution of a pump-turbine: Measurement and simulation of a rotating disk flow

Measurements of Heat Transfer and Pressure in a Trailing Edge Cavity of a Turbine Blade

Aerothermal Performance of Different Tips in Transonic Turbine Cascade with End-Wall Motion

Aerodynamic and Performance Behavior of A Radial Turbine at Design and Off-Design Conditions

Numerical investigation on the influence of nonuniform tip clearance on rotor tip-clearance flow field structure