Abstract:It may be a potential way to realize high-efficiency and high-quality local loading forming on the double-action press. However, the deformation characteristics and forming quality of transitional region are the weak link during forming process. In this work, the material flow, deformation inhomogeneity, forming defect of transitional region, and their dependences on the local loading parameters were quantitatively investigated by FE simulation. It is found that due to the constraint clearance, the web material would undergo twice transverse flow with opposite directions successively in two loading steps. This phenomen is basically the same as that in the local loading forming on single-action press, while the extent of transverse material flow on double-action press is greatly smaller. Finally, the transitional region presents different strain distributions in various sub-regions. Region A and region C present a symmetric strain concentration area at rib root, while region B presents a slant strain concentration area at the middle rib. The forming quality on double-action press is better than that on the single-action press. Only a cavum defect at left rib is produced because of the transverse material flow. Constraint clearance plays the most important role in the deformation characteristics and forming quality during the local loading forming on double-action press. The transverse material flow and cavum defect can be suppressed by decreasing the constraint clearance, but the deformation inhomogeneity would increase to some extent at the same time. In addition, the friction factor and radius of left rib are the second significant factors. Increasing the friction factor and radius of left rib is helpful to suppress the transverse material flow and cavum defect, respectively. As far as the forming quality of transitional region is concerned, it is a better way to conduct the local loading forming on double-action press than on single-action press. The results will provide basis for the design of processing parameters in the local loading forming of Ti-alloy rib-web component on double-action press.

Deformation Behavior of Variable-Thickness Region of Billet in Rib-Web Component Isothermal Local Loading Process

Deformation Characteristics of Transitional Region During Local Loading Forming of Ti-alloy Rib-Web Component on the Double-Action Press

Development of Transition Condition for Region with Variable-Thickness in Isothermal Local Loading Process

Unequal-thickness Billet Optimization in Transitional Region During Isothermal Local Loading Forming of Ti-alloy Rib-Web Component Using Response Surface Method

Deformation behavior under die partitioning boundary during titanium alloy large-scale rib-web component forming by isothermal local loading

Forming Defects Control in Transitional Region During Isothermal Local Loading of Ti-alloy Rib-Web Component

Metal Flow Characteristics of Local Loading Forming Process for Rib-Web Component with Unequal-Thickness Billet

Simulation on influence of local loading conditions on material flow during rib-web components forming

Influence of Die Parameters on the Deformation Inhomogeneity of Transitional Region During Local Loading Forming of Ti-alloy Rib-Web Component

Rib Filling Behavior in Flow Forming of Thin-Walled Tube with Helical Grid-Stiffened Ribs

Improving the Deformation Homogeneity of the Transitional Region in Local Loading Forming of Ti-alloy Rib-Web Component by Optimizing Unequal-Thickness Billet

Formation Mechanism, Prediction and Control of the Forming Defects in Transitional Region During Local Loading Forming of Ti-alloy Rib-Web Component

Flow defects of rib-web components in isothermal local-loading forming process

Quantitative Analysis of the Material Flow in Transitional Region During Isothermal Local Loading Forming of Ti-alloy Rib-Web Component

A non-sequential isothermal local-loading forming process for large-scale rib-web components

Unequal Thickness Billet Design for Large-Scale Titanium Alloy Rib-Web Components under Isothermal Closed-Die Forging

Loading state in local loading forming process of large sized complicated rib-web component

Analysis of Local Loading Forming for Titanium-Alloy T-Shaped Components Using Slab Method

Influence of the Billet Volume Distribution on Macro Deformation and Microstructure Response in Transitional Region of Ti-Alloy Multi-rib Component under Isothermal Local Loading

Forming Limit of Local Loading Forming of Ti-alloy Large-Scale Rib-Web Components Considering Defects in the Transitional Region

Research on local loading method for an aluminium-alloy hatch with cross ribs and thin webs