Abstract:It was known that frequency selective surfaces are commonly used in avionics (aircraft antennas, nose-cone radomes) and as polarizers, space filters, and sub-reflectors in dual frequency dish antennas. Recently researchers find that FSS can be used in any way that some sort of frequencydependent filtering of plane waves is desired. E.g. FSS can be used to boost the reflection of surfaces at specific bands which would aid collision avoidance systems by providing a larger return for them to focus on, or improve coupling to an RFID tag system, or can be tuned to only permit radiation at specific bands to provide a band-limited connection between waveguide elements, antennas, enclosures, or the like. With the newer PBG type surfaces, uses may also extend into patterned grounds which could improve the behaviour of planar antennas or even RF and microwave circuitry placed on top of these patterned ground structures. FSS is any periodic structure which is designed to have some sort of frequency-dependent behaviour characteristic. FSS formed by periodic patterns of simple elements on the Single layer dielectric substrate is easy to fabricate, but their performance is limited in terms of susceptibility to changes of polarization state and sensitivity of angle incidence [1]. Many approaches have been taken to improve the performance of FSS. Dielectric loading FSS and biplanar FSS have been studied by Leubber and Munk [1]. Different periodic elements have been discussed in papers of Shaker, Wu Tekao, et al. Complementary FSS, close coupled FSS and reconfigurable FSS have been analyzed by Vardaxoglou. Aperture coupled microstrip patch arrays of narrow passband FSS with high selectivity performance has been investigated by Pous. Rapid roll-off FSS with super dense stacked patch has been illuminated by Parker. All above attempts have improved parts of the performance of FSS. But for its low quality factor (Q) of open resonance structure, the performance of these types FSS is not perfect as expect. Recently, substrate integrated waveguide (SIW) technology has been used in FSS design [2], in which SIW has been used to form a cavity structure in conventional periodic aperture FSS. It is known that SIW structure keeps the advantages of conventional metallic waveguides. In this paper, SIW technique combined hybrid metallic ring is applied to design band-pass FSS. The structure of this type FSS is simple and thickness of stratified dielectric slab is thin. It takes the advantages of low insertion loss in pass-band and its performance is insensitive to the incident angles and polarization. Simulation and experiment results show that this new scheme is feasible.

A Novel Fss Based on Hybrid Boundary Condition Cavity

A Novel Frequency Selective Surface with Smaller Size and Wide Band

A Bandpass Frequency Selective Surface With a Low Cross-Polarization Based on Cavities With a Hybrid Boundary

A Novel Dual-Band Frequency Selective Surface (FSS)

Bandpass Frequency Selective Surface with Two Sharp Sidebands Based on Shunted Quarter‐mode Substrate Integrated Waveguide Cavities

Novel Frequency Selective Surface with Quasi-Elliptic Response

A Novel Angularly Stable Wide Passband Frequency Selective Surface

Filtenna-Filtenna Design for Broadband and High-Selectivity Frequency Selective Surface

A Novel Narrow-band Bandpass Frequency Selective Surface

A Novel Miniaturized Frequency Selective Surface with Stable Responses

Dual-band Frequency Selective Surface with Quasi-Elliptic Bandpass Response

A Hybrid 2-D–3-D Miniaturized Multiorder Wide Bandpass FSS

A Novel Miniaturized Dual-band Frequency Selective Surface

A NOVEL DUALBAND FREQUENCY SELECTIVE SURFACE WITH PERIODIC CELL PERTURBATION

Design of a Three-dimensional Bandpass Frequency Selective Surface Based on Coupled-slotlines

A Novel Band-Reject Frequency Selective Surface with Pseudo-Elliptic Response

A FSS of Hybrid Combined Elements for Dual-Band Operations

Dual-Band High Selective Frequency Selective Surface Design and Analysis

A Modified High-Selective Frequency Selective Surface Designed by Multilevel Green's Function Interpolation Method

A Hybrid Ring Frequency Selective Surface Based on SIW Technology

A Dual-Polarized Bandpass Frequency Selective Surface With Stable Response