Abstract:Frequency multipliers and mixers based on Schottky barrier diodes (SBDs) are widely used in terahertz (THz) imaging applications. However, they still face obstacles, such as poor performance consistency caused by discrete flip-chip diodes, as well as low efficiency and large receiving noise temperature. It is very hard to meet the requirement of multiple channels in THz imaging array. In order to solve this problem, 12-μm-thick gallium arsenide (GaAs) monolithic integrated technology was adopted. In the process, the diode chip shared the same GaAs substrate with the transmission line, and the diode’s pads were seamlessly connected to the transmission line without using silver glue. A three-dimensional (3D) electromagnetic (EM) model of the diode chip was established in Ansys High Frequency Structure Simulator (HFSS) to accurately characterize the parasitic parameters. Based on the model, by quantitatively analyzing the influence of the surface channel width and the diode anode junction area on the best efficiency, the final parameters and dimensions of the diode were further optimized and determined. Finally, three 0.34 THz triplers and subharmonic mixers (SHMs) were manufactured, assembled, and measured for demonstration, all of which comprised a waveguide housing, a GaAs circuit integrated with diodes, and other external connectors. Experimental results show that all the triplers and SHMs had great performance consistency. Typically, when the input power was 100 mW, the output power of the THz tripler was greater than 1 mW in the frequency range of 324 GHz to 352 GHz, and a peak efficiency of 6.8% was achieved at 338 GHz. The THz SHM exhibited quite a low double sideband (DSB) noise temperature of 900~1500 K and a DSB conversion loss of 6.9~9 dB over the frequency range of 325~352 GHz. It is indicated that the GaAs monolithic integrated process, diodes modeling, and circuits simulation method in this paper provide an effective way to design THz frequency multiplier and mixer circuits.

A Terahertz Frequency Tripler with Single Serial Varactor Diode

Design of a 225ghz Frequency Broadband Solid State Tripler

Design of a 340ghz Balanced Frequency Tripler

An 18 similar to 30 GHz Vector-Sum Phase Shifter With Two-Stage Transformer-Based Hybrid in 130-nm SiGe BiCMOS

A Wideband CMOS Frequency Quadrupler with Transformer-Based Tail Feedback Loop.

A Ka and V Band Voltage-Controlled Oscillator for Terahertz Application in GaAs with Start-Up Relaxation

An 18~30 GHz Vector-Sum Phase Shifter with Two-Stage Transformer-Based Hybrid in 130-Nm SiGe BiCMOS

325Ghz Balanced Tripler Based on Schottky Diode

A 315–345 GHz quad‐port balanced tripler with inherent suppressions on even‐order harmonics using discrete Schottky diodes

A 220 GHz Frequency Tripler Based on AlN Substrate

24.3 A 200-to-350ghz SiGe BiCMOS Frequency Doubler with Slotline-Based Mode-Decoupling Harmonic-Tuning Technique Achieving 1.1-to-4.7dbm Output Power

A Novel Balanced Frequency Tripler With Improved Power Capacity for Submillimeter-Wave Application

Development of 340-GHz Transceiver Front End Based on GaAs Monolithic Integration Technology for THz Active Imaging Array

Design of High Power Tripler Based on On-Chip Schottky Diodes

A 170‐ to 260‐GHz Full‐Band Frequency Doubler Realized by Impedance Compression Matching Technique

Optimization of Terahertz Monolithic Integrated Frequency Multiplier Based on Trap-Assisted Physics Model of THz Schottky Barrier Varactor

Design of W-Band Tripler

A 135–150-Ghz Frequency Tripler with Waveguide Filter Matching

A Novel 220-Ghz GaN Diode On-Chip Tripler with High Driven Power

A 220 GHz High-Efficiency Doubler Based on Function-Based Harmonic Impedance Optimization Method

Design of A Microwave Frequency Tripler with Conversion Gain