Abstract:Mg–6.0 Zn–2.0 Yb–0.5 Zr (wt.%) alloy exhibits excellent strength and ductility synergy after thermomechanical and heat treatment. Unfortunately, the hot workability and microstructure evolution under specific deformation regimes remain uncertain to date. In this work, the constitutive model and hot processing maps were established based on a series of isothermal compression tests. A detailed examination of deformation microstructures at different processing regimes revealed that the hot workability and correlated microstructure development were deformation condition dependent. When compressed at lower strain rates and higher deformation temperatures, the softening was promoted by dynamic recrystallization (DRX) and the prevalence of discontinuous dynamic recrystallization (DDRX) generally resulted in a complete DRX process with coarse grains and much-intensified texture. On the contrary, work hardening was improved with increasing dislocation density, and the continuous DRX (CDRX) may control the partial DRX progress, often presenting a much-refined microstructure with a more dispersed texture. Interestingly, a low strain rate of 0.001 s −1 and a moderate deformation temperature of 300 °C effectively balanced the nucleation rate and grain growth to finally achieve a much refined and relatively homogeneous grain structure. Further investigation concerning the activation energy suggested that the workability improved with increasing strain rate and temperature. Enhanced hot workability at most deformation regimes was achieved due to a lower average activation energy Q value in comparison with that of 1.0 wt.% Yb alloyed ZK60 counterpart, which was likely due to a higher activity of non-basal slips achieved in this alloy.

Uniform Fine Microstructure and Random Texture of Mg–9.8Gd–2.7Y–0.4Zr Magnesium Alloy Processed by Repeated-Upsetting Deformation

Microstructural Evolution and Mechanical Properties of Mg-9.8Gd-2.7Y-0.4Zr Alloy Produced by Repetitive Upsetting

Finite Element Simulation and Experimental Investigation on Homogeneity of Mg-9.8Gd-2.7Y-0.4Zr Magnesium Alloy Processed by Repeated-Upsetting

Hot Deformation and Processing Map of As-Homogenized Mg–9Gd–3Y–2Zn–0.5Zr Alloy

Deformation Behavior, Microstructure Evolution and Hot Workability of Mg-3.7Gd-2.9Y-0.7Zn-0.7Zr Alloy

Microstructure and Texture Evolution of Mg-Gd-Y-Zr Alloy during Reciprocating Upsetting-Extrusion

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructure Evolution and Mechanical Properties of Mg-10.37Gd-3.66Y-2.27Zn-0.52Zr Alloy during Reciprocating Upsetting-Extrusion

Grain refinement and weak-textured structures based on the dynamic recrystallization of Mg-9.80Gd-3.78Y-1.12Sm-0.48Zr alloy

Microstructures and Mechanical Properties of Mg-10Gd-3Y-2Zn-0.5Zr Alloy

Microstructure Evolution and Mechanical Properties of Az91d Magnesium Alloy Processed by Repetitive Upsetting

Deformation mechanism of fine grained Mg–7Gd–5Y–1.2Nd–0.5Zr alloy under high temperature and high strain rates

Microstructure, Mechanical Properties and Texture Evolution of Mg–Al–Zn–La–Gd–Y Magnesium Alloy by Hot Extrusion and Multi-Pass Rolling

Microstructural Evolution and Mechanical Properties of Mg-5y-5gd-Xnd-0.5zr Magnesium Alloys at Different States

The abnormal flow behavior of Mg-9Gd-4Y-2Zn-0.5Zr alloy during hot tensile deformation at high temperature and low strain rate

Deformation Behavior of Ultra-Strong and Ductile Mg-Gd-Y-Zn-Zr Alloy with Bimodal Microstructure

High Performance Mg Alloy with Designed Microstructure and Phases

Tuning texture and precipitation using Y/Gd atomic ratio in iso-concentration Mg–Y–Gd–Ag–Zr extruded alloys

Microstructures evolution, texture characteristics and mechanical properties of Mg-2.5Nd-0.5Zn-0.5Zr alloy during the high strain rate hot-rolling

The Partial Substitution of Y with Gd on Microstructures and Mechanical Properties of As-Cast and As-Extruded Mg-10Zn-6Y-0.5Zr Alloy

Hot workability and microstructure of Mg–6.0 Zn–2.0 Yb–0.5 Zr magnesium alloy