Abstract:Spout-fluid beds are widely used in the process industry due to their facilitation of an efficient contact between particles and gas. In this paper, a two-fluid model (TFM) is set up to reproduce the various flow structures encountered during spout-fluid bed operation. The effects of normal restitution model and gas-solid drag model are assessed by comparing simulation results with the experimental and discrete particle modeling (DPM) data of Link et al. [Link et al. Chem. Eng. Sci. 2005, 60, 3425-3442; Link et al. AIChE J. 2008, 54, 1189-1202.]. Simulation results show that application of an effective restitution coefficient in TFM can improve the accuracy of prediction significantly. The drag model of HKL predicts a more reasonable result than models of Huilin-Gidaspow, BVK, and Syamlal and O'Brien. Analysis on relative contributions of kinetic motion, friction, and collision to particle-particle momentum transfer parameters, namely, particle pressure and viscosity, shows that particle-particle momentum transfer in the spout and fountain regions is dominated by kinetic motion and that in the annulus region is dominated by friction. A transition region between spout and annulus regions is proposed. This region can be delineated using a single parameter of dimensionless collisional particle pressure because in this region, particle pressure is dominated by the collisional contribution. With an increasing spout-fluid ratio, the stable spout-annulus-fountain structure gradually shifts to an unstable bubble-slug structure. The effect of collision increases and extends to the entire bed. Meanwhile, the effects of kinetic motion and friction decrease. When slugs are formed, a rebound in the influence of friction is observed, accompanied by a decrease in the influence of collision.

CFD Simulation of Hydrodynamic Characteristics in a Multiple-Spouted Bed

Experimental and Numerical Investigations of Scale-Up Effects on the Hydrodynamics of Slurry Bubble Columns

Experimental and numerical investigation of solid behavior in a gas–solid turbulent fluidized bed

CFD Simulation of an Agitated Gas-Fluidized Bed: Effects of Particle–particle Restitution Coefficient on the Hydrodynamics

CFD Simulation and Experiments of Dynamic Parameters in Gas–solid Fluidized Bed

Experimental Investigation on Gas-Solid Hydrodynamics of Coarse Particles in A Two-Dimensional Spouted Bed

CFD simulation of effects of the configuration of gas distributors on gas–liquid flow and mixing in a bubble column

Numerical Simulation of Two-Dimensional Spouted Bed with Draft Plates by Discrete Element Method

Three-Dimensional Modeling of Gas–Solid Motion in a Slot-Rectangular Spouted Bed with the Parallel Framework of the Computational Fluid Dynamics–Discrete Element Method Coupling Approach

CFD‐DEM Simulation of the Spout–annulus Interaction in a 3D Spouted Bed with a Conical Base

A CFD-DEM study of a two-joint spouting flow pattern in a multiple rectangular spout fluidized bed

Two-Fluid Simulation of a Three-Dimensional Spout-Fluid Bed: Flow Structures, Regimes, and Insight into the Mechanism of Particle–Particle Momentum Transfer

Investigation of fluidization behavior of high density particle in spouted bed using CFD–DEM coupling method

Comparison of Euler-Euler and Euler-Lagrange Approaches for Simulating Gas-Solid Flows in a Multiple-Spouted Bed

Numerical Study of a Lab-Scale Double Slot-Rectangular Spouted Bed with the Parallel CFD–DEM Coupling Approach

Numerical Simulation of Spouting of Cylindroid Particles in A Spouted Bed

Numerical Investigation of the Time-Related Properties of Solid Phase in a 3-D Spout-Fluid Bed

Parallel CFD–DEM Modeling of the Hydrodynamics in a Lab-Scale Double Slot-Rectangular Spouted Bed with a Partition Plate

Computational Evaluation of Depth Effect on the Hydrodynamics of Slot-Rectangular Spouted Bed

Experimental and Cfd Study on the Hydrodynamic Characters of Dense Liquid-Solid Fluidized Bed

Effect of Operating Parameters on Gas‐Solid Hydrodynamics and Heat Transfer in a Spouted Bed