Abstract:Some recent studies have highlighted the potential of adsorption technology for greenhouse gas CO2 capture from the flue gases. The pressure/vacuum swing adsorption (PSA/VPSA), temperature swing adsorption (TSA) and electrical swing adsorption (ESA) have attracted much research effort with the development of the novel CO2 adsorbents materials. Carbonaceous materials are the promising candidate adsorbents, since they have high BET surface area, better CO2 adsorption capacity and novel morphologies (monolith, bead, fiber). Moreover, these adsorbents materials are also unique to undergo direct-electrothermal regeneration. In this paper, carbonaceous materials with four morphologies (granular, monolith, fiber and bead) are used to capture CO2 from the flue gas. Activated carbon beads were made in our laboratory with 2000-3000 m2/g BET surface area and better electrical conductivity. The research contents include the adsorption equilibrium isotherms, breakthrough curves, electrical energy consumption at direct-electrothermal desortpion, and the optimization of the cycle adsorption/desorption processes. The experimental apparatus for the optimization of the cycle adsorption/Direct-electrothermal desorption process comprise an adsorber with 40-100mm height and 25-50mm diameter, an electricity heating unit, a cooling unit, a vacuum unit, a gas detection unit, a data acquisition and control system. The heating step by electricity is very fast, about 2-5 minutes to raise the temperature of adsorbents from 30°C to 150°C when using 50 V voltages. But the cooling step is very slow due to the poor heat conductivity of porous adsorbents, so the alternative cooling units are designed, one using the direct cooling unit with air or nitrogen passing through the column, the other one as the indirect cooling unit by the medium of water or heat transfer oil indirect cooling adsorbents. Three processes of the cycle adsorption/desorption to capture CO2 from the flue gases using carbonaceous materials are investigated, which included the conventional vacuum swing adsorption process, the electrical swing adsorption process, and the combined process of vacuum swing adsorption and direct-electrothermal regeneration. The mathematical models are proposed for different capture processes using activated carbons with four morphologies (granular, monolith, fiber, beads). Based on the experimental and theoretical investigations, the product recovery, purity, and the energy consumption of the adsorption processes for CO2 capture from the flue gas are compared, and the feasibilities of the capture processes using carbonaceous materials are evaluated comprehensively.

Experimental and Modeling Investigation on Post-Combustion Carbon Dioxide Capture Using Zeolite 13X-APG by Hybrid VTSA Process

Zeolite Apgiia for Adsorption Based Carbon Dioxide Capture

Onsite Co2 Capture from Flue Gas by an Adsorption Process in A Coal-Fired Power Plant

A combined process of vacuum and temperature swing adsorption for post-combustion CO2 capture

Capture of CO2 from Flue Gases by a Combined Process of Vacuum and Temperature Swing Adsorption Using 13X-APG Zeolite

Post-combustion CO2 capture from a natural gas combined cycle power plant using activated carbon adsorption

Design and development of 3D hierarchical ultra-microporous CO2-sieving carbon architectures for potential flow-through CO2 capture at typical practical flue gas temperatures

Process design and adsorbent screening of VSA and exchanger type VTSA for flue gas CO 2 capture

A Combined Process of Vacuum and Temperature Swing Adsorption for CO2 Capture using 5A Molecular Sieve

Multi-bed Vacuum Pressure Swing Adsorption for Carbon Dioxide Capture from Flue Gas

Experimental evaluation of adsorption technology for CO2 capture from flue gas in an existing coal-fired power plant

Capture of CO 2 from Flue Gas by Vacuum Pressure Swing Adsorption Using Activated Carbon Beads

Co2 Capture from Flue Gas by Two Successive Vpsa Units Using 13Xapg

Two-Stage Vpsa Process for Co2 Capture from Flue Gas Using Activated Carbon Beads

Carbon dioxide capture by adsorption of carbonaceous materials with direct-electrothermal desorption

Co2 Capture from Flue Gas in an Existing Coal-Fired Power Plant by Two Successive Pilot-Scale Vpsa Units

Thermodynamic Exploration of Two-Stage Vacuum-Pressure Swing Adsorption for Carbon Dioxide Capture

CO 2 capture using low silica X zeolite synthesized from low-grade coal gangue via a two-step activation method

Microporous Carbon Coated Zeolite Particles for Efficient Carbon Capture from Wet Flue Gas

Recent Developments and Consideration Issues in Solid Adsorbents for CO 2 Capture from Flue Gas

Combined Grand Canonical Monte Carlo and Finite Volume Method Simulation Method for Investigation of Direct Air Capture of Low Concentration CO2 by 5A Zeolite Adsorbent Bed