Abstract:Due to the excellent heat transfer performance and adaptability in dealing with local hot spots, jet array impingement boiling is promising for the high heat flux cooling in a variety of power electrical and electronic devices, such as high-performance CPU, IGBT, and laser diode. A distributed jet array with effusion ports adjacent to jet holes can extract spent flow immediately to avoid the negative crossflow effect in a normal jet array. Consequently, the heat transfer coefficient (HTC) and critical heat flux (CHF) can be both improved greatly. In order to further improve the heat transfer performance of distributed jet array impingement boiling, enhanced boiling surfaces could be used. Particle sintered porous surfaces have been widely investigated in pool boiling and achieved significant enhancement effect owing to the increased nucleation sites and wetting areas. Although several studies on the sintered porous structure have been done for jet impingement boiling, none is for distributed jet array. In this paper, a pumped two-phase loop was built up and three kinds of porous surfaces were experimentally investigated to enhance the distributed jet array impingement boiling of dielectric coolant, HFE7000. The porous structures were sintered with the copper particles of 50, 100 and 200 mu m in diameter on a target surface of 11 mmx20 mm and had a fixed thickness to particle size ratio of 2.0. A distributed jet array with 10 jet holes and 12 effusion holes was used. The diameters of the jet and effusion holes were 1 mm and 2 mm, respectively, while the distances between jet holes or effusion holes were 5 mm. The volume flow rate through the test section was 0.4 L/min, and the liquid inlet temperature and phase change saturation temperature were controlled at 35 and 60 degrees C, respectively. An experimental apparatus was also established up to compare the wickability of the three porous surfaces. The 100 and 200 mu m particles sintered surfaces were proved to have the better wickability. The experimental results turn out that the single-phase heat transfer is significantly improved due to the increased heat transfer area and flow turbulence within the porous structures, and the enhancement ratio increases with the increasing of flow rate. The porous surfaces sintered with 100 and 200 mu m particles have close heat transfer performances, which are much better than that sintered with 50 mu m particles. As for boiling heat transfer regime, the porous structures can provide more nucleation sites but at the same time will increase the flow resistance of effusion vapor. As a trade-off, the best performance is achieved by 100 mu m particle, with its largest heat transfer coefficient upon DNB (departure from nucleate boiling) increased by 61% compared with that of the smooth surface. The wickability of porous layer however has no obvious effect on CHF due to the dominant role of distributed jet impingement on liquid feeding as well as the low surface tension of HFE7000. The maximum enhancement of CHF by 17% is acquired using the 100 mu m particle sintered porous surface. Nevertheless, the heat flux range between DNB and CHF is greatly extended for the porous surfaces, which is beneficial to practical applications. A number of spots are found to be randomly distributed on the original smooth particle surfaces after many times of boiling experiments, but seem to have little influence on heat transfer performance. The long-term durability of the enhancement surface however needs further investigation.

Experimental studies of flow boiling heat transfer in sintered/stacking porous media

Experimental investigation on heat transfer of flow boiling in stacking porous media

Theoretical and Experimental Investigation of Flow Rate Characteristics of Sintered Metal Porous Media

Study of enhanced heat transfer performance of subcooled and saturated flow boiling with R365mfc on sintered porous coating high heat flux tubes

EXPERIMENTAL STUDY ON BOILING FLOW AND HEAT TRANSFER IN PEBBLE BED CHANNELS

Effects of Structural Parameters on Flow Boiling Performance of Reentrant Porous Microchannels

Experimental Investigation into Flow Boiling Heat Transfer and Pressure Drop in Porous Coated Microchannels

Subcooled Flow Boiling With Sintered Porous Coatings In Small Channel

Experimental And Numerical Investigation Of Transpiration Cooling For Sintered Porous Flat Plates

Experimental Investigation on Narrow Gap Heat Transfer with Porous Media under Downward-Facing Horizontal Heated Surface

An Experimental Study of Two Phase Flow and Boiling Heat Transfer in Bi-Dispersed Porous Channels

Experimental Research on Convection Heat Transfer in Sintered Porous Plate Channels

Characterizing Effect of Particle Size on Flow Boiling in Sintered Porous-Microchannels

Experimental and Numerical Investigation of Forced Convection Heat Transfer of Air in Non-Sintered Porous Media

Effects of Heat Flux, Mass Flux and Channel Size on Flow Boiling Performance of Reentrant Porous Microchannels

Flow boiling characteristics in porous heat sink with reentrant microchannels

EXPERIMENTAL INVESTIGATION OF HEAT TRANSFER OF SUPERCRITICAL CO_2 IN SINTERED POROUS MEDIA

Experimental Study on Forced Convective Heat Transfer in Structured Packed Porous Media with Spherical or Ellipsoidal Particles

Boiling Phenomenon and Heat Transfer in Bead-packed Porous Structure

Investigation of Supersonic Transpiration Cooling Through Sintered Metal Porous Flat Plates

Distributed jet array impingement boiling on particle sintered porous surfaces