Abstract:In the present study, 7005 aluminum alloy billets were supplied in the warm extruded and T6 heat treated state. They were then reheated to the semisolid state and the microstructural evolution and coarsening investigated. This is necessary groundwork if the billets are to be formed to shape by semisolid processing, an innovative manufacturing route which has recently gained wide use for a range of aluminum alloys but which has not yet been applied to 7005. The results showed that the average spheroid size, liquid film thickness and liquid fraction of 7005 aluminum alloy increased with increase in soaking time. Intragranular liquid droplets were present in solid grains, and coarsened with increase in soaking time and isothermal temperature. The roundness of globules of solid in the semisolid state at 600°C–615°C was in the range of 1.5 to 2.0 after soaking for periods up to 12min at 620°C, but for times greater than 15min was more than 2, which is unlikely to be suitable for the semi-solid forming process, where smooth flow is required and therefore relatively round globules. When the isothermal temperatures were 600°C, 610°C, 615°C and 620°C, the coarsening rates were 542μm3s−1, 606μm3s−1, 683μm3s−1 and 688μm3s−1, respectively. The coarsening rate K increased with the increase of isothermal temperature. These values place this alloy on the dividing line between typical coarsening rates for normally cast alloys and typical coarsening rates for normally wrought alloys. This is attributed to the fact that the alloy has a relatively simple precipitation hardening system in comparison with other 7xxx alloys and the hardening precipitate (MgZn2) melts below the temperature the experiments have been carried out at, hence preventing the precipitates inhibiting liquid film migration and diffusion along narrow liquid films at spheroid boundaries. Coarsening tends to occur via Ostwald ripening and coalescence, but Ostwald ripening plays an increasing role with the increase of isothermal temperature.

Microstructural Evolution of A356.2 Alloy Prepared by the SIMA Process

Microstructural Features and Wear Characteristics of Semi-Solid Processed A356 Aluminum Alloy

Microstructure and Texture Evolution of 2A12 Aluminum Alloy Semi-Solid Billet Prepared by SIMA Process

Microstructures of Semi-Solid AZ91D Magnesium Alloys Billets Prepared by Cold Rolling SIMA Method

Deformation Behaviour and Microstructures of Semi-Solid A356.2 Alloy Prepared by Radial Forging Process During High Solid Fraction Compression

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

The Effect of Initial Microstructure of A356 Alloys on the Mechanical Behavior in the Semisolid State

Isothermal Semisolid Microstructure Evolution of Compressively Deformed AZ91D Magnesium Alloy Billet

Microstructural Coarsening of 6061 Aluminum Alloy Semi-Solid Billets Prepared Via Recrystallization and Partial Melting

Numerical Simulation and Experimental Investigation of Microstructure Evolution and Flow Behavior in the Rheological Squeeze Casting Process of A356 Alloy

Microstructure Evolution of AZ91D Magnesium Alloy Semi-solid Billets Prepared by a New SIMA Method

The Influences of the Microstructure Morphology of A356 Alloy on Its Rheological Behavior in the Semi-Solid State

Effects of Temperature and Time on Microstructural Evolution of Semisolid 5A06 Aluminum Alloy: Preparation of Semisolid Billets in Ellipsoid Solid Phase

Effect of Isothermal Process Parameters on Semi-Solid Microstructure of Chip-Based Al–Cu–Mn–Ti Alloy Prepared by SIMA Method

Microstructural Coarsening of 7005 Aluminum Alloy Semisolid Billets with High Solid Fraction

Structural Evolution of LC 4 Alloy in Making Thixotropic Billet by SIMA Method

A New Technology to Improve the Elongation of A356 Alloy

Recrystallization of Hot-Rolled 2A14 Alloy during Semisolid Temperature Annealing Process

Microstructural Features of Semi-Solid A357 Alloy Slurry Under High-Shear Melt Processing

Effects of Solid–Liquid Mixing on Microstructure of Semi-Solid A356 Aluminum Alloy

Microstructural Evolution in a 6060 Extrudable Al-Alloy: Integrated Modeling and Experimental Validation