Abstract:Objectives: Occipitocervical fusion (OCF) is an effective treatment for instability of occipitocervical junction (OCJ). The occipital condyle screw serves as a novel surgical technique for occipitocervical fixation. However, the intraoperative procedures for the occipital condyle screw technique have relied on surgeons' experience, so the pool of surgeons who are able to perform this surgery safely is limited. The present study aims to evaluate the feasibility and safety of the occipital condyle screw technique using human cadavers and to provide image anatomy for clinical application basis. Methods: The scientific study comprised 10 fresh-frozen cadaveric specimens from the anatomy department of Qingdao University. Placement of the occipital condyle screws (3.5 mm diameter and 20.0 mm length) was performed in the 10 fresh-frozen cadaveric specimens with intact occipitocervical junctions, respectively. Occipitocervical CT was performed for all specimens and the DICOM data was obtained. Occipitocervical CT three-dimensional (3D) reconstruction was performed for the cadavers. Morphometric analysis was performed on the bilateral occipitocervical junction of 10 cadaveric specimens based on the 3D reconstruction CT images. Detailed morphometric measurements of the 20 occipital condyles screws were conducted including the average length of the screw trajectory, inside and upper tilting angles of screws, distance to the hypoglossal canal, and to the medial wall of occipital condyle. Results: Placement of the occipital condyle screws into the 20 occipital condyles of the 10 cadaveric specimens was performed successfully and the trajectory of implantation was satisfactory according to 3D CT reconstruction images, respectively. There was no obvious injury to the spinal cord, nerve root, and vertebral artery. The length of the bilateral screw trajectory was, respectively, 20.96 ± 0.91 mm (left) and 20.59 ± 0.77 mm (right) (t = 1.306, P > 0.05). The upper tilting angle of bilateral screws was, respectively, 11.24° ± 0.74° (left) and 11.11° ± 0.64° (right) (t = 0.681, P > 0.05). The inside tilting angle of bilateral screws was, respectively, 31.00° ± 1.32° (left) and 30.85° ± 1.27° (right) (t = 0.307, P > 0.05). The screw's distance to the bilateral hypoglossal canal was, respectively, 4.84 ± 0.54 mm (left) and 4.70 ± 0.54 mm (right) (t = 0.685, P > 0.05). The screw's distance to the medial wall of the bilateral occipital condyle was, respectively, 5.13 ± 0.77 mm (left) and 5.04 ± 0.71 mm (right) (t = 0.384, P > 0.05). Conclusion: The occipital condyle screw technique can serve as a feasible and safe treatment for instability of the occipitocervical junction with meticulous preoperative planning of the screw entry point and direction based on individual differences. Morphometric trajectory analysis is also an effective way to evaluate the surgical procedure.

Strain electronic measurements on craniovertebral junction fixation with posterior screw technique

Strain electronic measurements of posterior screws inserted to craniovertebral junction

Biomechanical and Clinical Study of Anterior Transarticular Screw Fixation for Treatment of Traumatic Instability of C1-C2 Joint

Anatomical measurements and clinical significance of anterior atlantoaxial transarticular screw fixation

Progression of Research of Posterior Screw Fixation on Atlas

The biomechanical study of craniovertebral junction fixation with posterior transarticular screw]

Biomechanical stability of atlantoaxial and occipitocervical fixations with unilateral spinous process screw plus contralateral pedicle screw: a finite element analysis

The Biomechanical Study on Four Internal Fixation Techniques for Occipitocervical Spine

Anatomical Study of Posterior Atlanto-Occipital Transarticular Screw Fixation

Biomechanical analysis of direct posterior C1 screws compression reduction in the selective treatment of unstable atlas fractures

Single use of transarticular screws in atlantoaxial instability

In Vitro Stability Analysis Of The Three-Pronged Mayfield Head Clamp Using Pins In Four Different Positions On The Skulls

SAFE ANGLE SCOPE FOR POSTERIOR ATLANTO-OCCIPITAL TRANSARTICULAR SCREW FIXATION

Morphometric Trajectory Analysis for Occipital Condyle Screws

The Study on the Feasibility of Posterior Occipitoatlantoaxial Transarticular Screw Fixation

Biomechanical evaluation of C1 lateral mass and C2 translaminar bicortical screws in atlantoaxial fixation: an in vitro human cadaveric study

Biomechanical differences of three cephalic fixation methods for patients with basilar invagination and atlantoaxial dislocation in the setting of congenital atlas occipitalization: a finite element analysis

The Measurement of Trajectory Parameters in Posterior Atlanto-Occipital Transarticular Screw Fixation

A Technique for the In Vivo Study of Three-dimensional Cervical Segmental Motion Characteristics After Anterior Screw Fixation for Odontoid Process Fractures

Quantitative anatomy of three types screw fixation technique of posterior approach for axis

Feasibility of Screw Placement in the Occipital Condyle of Chinese Patients for Occipitocervical Arthrodesis: A Cadaveric Study