Abstract:LBE-cooled fast reactor (LBFR) has a promising application prospect in energy generation and transmutation of highlevel radioactive waste. Wirewrapped fuel rods are usually used in LBFR to reach high heat transfer efficiency and selfsupport. The wire spacer has a great influence on the transverse flow and interchannel mixing, and leads to a nonuniform temperature profile over the fuel rod surface. Therefore, accurate prediction of the transverse flow mixing characteristics in the wirewrapped bundle channel is the basis of thermalhydraulic safety analysis of LBFR. In the present study, a CFD modeling and simulation for a LBEcooled 7pin wirewrapped fuel assembly was carried out based on RANS method. The simulation results were firstly compared with the experimental data from the literature. A good agreement demonstrated the capability of the employed approach to predict the flow field in the rod bundle. Then, the threedimensional transverse flow mixing behaviors of LBE in single wirewrapped fuel and multi wire-wrapped fuel assemblies were analyzed in detail. The results show that the maximum transverse flow velocity in the central sub-channel of the single wirewrapped fuel assembly does not exceed 19% of the axial flow velocity. The transverse flow direction and secondary flow center change periodically with height. In the single wirewrapped fuel assembly, the transverse flow at the interface of the central subchannel is distributed as a trigonometric function along the axis. When the wire spacer coincides with the interface of the central subchannel，the transverse flow and the transverse flow mixing index tend to zero. When the wire spacer is perpendicular to the interface, the transverse flow and the transverse flow mixing index reach the peak. The transverse flow mixing index is not sensitive to Reynolds number in the turbulent zone, but is strongly correlated to the structural parameters of the assembly, which means that the lateral mixing in the wirewrapped bundle is dominated by the flow sweeping mechanism, rather than turbulent mixing. Compared with the single wire-wrapped fuel assembly, the transverse flow distribution of the multi wirewrapped fuel assembly is more uniform and more secondary flow vortex can be observed. The swirling directions of the LBE around the two adjacent fuel rods in the multi wirewrapped fuel assembly are opposite. That is, there are two opposite transverse flow directions on the interface of the central subchannel in the multi wirewrapped fuel assembly.

Numerical Analysis of the Lifting Beam's Influence on Flow Fields in Planar Fuel Assemblies

Study on Dynamic Pressure Effect of Gas Bearings in Fuel Cell Vehicles

Numerical Simulation of Temperature Fields in Planar Fuel Assembly

Numerical investigation of flow past two elliptical cylinders in side-by-side arrangement via lattice Boltzmann-fictitious domain method

Numerical investigation on critical heat flux for 5 × 5 fuel assemblies with a wide range of working conditions

Simulation of Flows Around Two Tandem Rotating Cylinders in a Channel Using LB-DF/FD Method

Flow Distribution Characteristics of Parallel Narrow Rectangular Channels under Deformation Conditions -Part II: Numerical Model

CFD investigation for a 7-pin wire-wrapped fuel assembly with different shapes of fuel duct wall

Numerical study of the flow and heat transfer characteristics within the annular fuel element with double-sided cooling

Numerical Simulation of High Temperature Reactor Fuel Element Aerodynamic Lifting Process

Studies on the Critical Heat Flux in Fuel Assembly Using a Modified Two-Phase Multi-Scale Interface Model-Validation and Sensitivity Analysis

Numerical Study on the Boiling Heat Transfer and Critical Heat Flux in a Simplified Fuel Assembly with 2×2 Helical Cruciform Rods

CFD analysis for full vessel upper plenum in Maanshan Nuclear Power Plant

Flow Distribution Characteristics of Parallel Narrow Rectangular Channels under Deformation Conditions -Part I: an Experimental Study

Numerical simulation of flow and heat transfer in fuel assembly of floating nuclear power platform

Analysis of Transverse Flow Characteristics in LBE-cooled Wire-wrapped Fuel Assembly

Numerical analysis of flow-induced deflection of curved nuclear reactor fuel plates under high velocity flows

A Key Geometric Parameter for the Flow Uniformity in Planar Solid Oxide Fuel Cell Stacks

Thermal-fluid-structure Coupling Analysis for Plate-Type Fuel Assembly under Irradiation. Part-I Numerical Methodology

Numerical Simulation of Heat Transfer and Fluid Flow During Double-Sided Laser Beam Welding of T-Joints for Aluminum Aircraft Fuselage Panels

CFD investigation of flow hydrodynamics and optimization in an industrial‐scale annular lance with swirl flow