Abstract:A normal composite wall panel is a structural component composed of polystyrene insulation boards and concrete surface layers reinforced with steel wire mesh. It can be entirely prefabricated in a factory or constructed with the concrete surface layers cast on-site. A novel prefabricated monolithic concrete–polystyrene panel composite wall panel (CPC wall panel) is proposed in this study. The CPC panel features a middle part that is prefabricated in the factory while the reinforced concrete regions at its two side ends are cast on-site. To evaluate the seismic performance of the wall panel, 18 CPC specimens were designed, manufactured, and quasi-statically tested, through which the structural behaviors, failure mode, and load-bearing capacity were studied. In addition, the influences of the height-to-width ratio and the vertical compressive stress level on the seismic performance of the CPC panels were also investigated. The test results showed that the connectors spaced at 400 mm × 500 mm could ensure the concrete layers on both sides of the polystyrene board worked collectively under seismic conditions. When subjected to lateral loads, the interface between the newly poured concrete and the existing concrete exhibited good bonding. Moreover, the failure mode of the CPC wall panel was largely correlated to the height-to-width ratio that, for specimens having four steel bars of 12 mm diameter and a height-to-width ratio greater than 1, the flexural failure was initially developed, followed by diagonal shear failure. In specimens with a height-to-width ratio of 1, flexural and diagonal shear failures occurred almost simultaneously. For specimens with a height-to-width ratio of less than 1, the final diagonal shear failure was predominant. The longitudinal reinforcing bars at the two ends of the CPC panels could effectively improve their lateral load-bearing capacity, with the enhancement influenced by the height-to-width ratio, the vertical load applied to the wall panel, and the cross-sectional area of the steel bars. In practice, the lateral load-bearing capacity of the CPC panel can be conservatively evaluated using the calculation method of the reinforced concrete shear walls. Finally, the ductility of the CPC specimens was affected by the height-to-width ratio and the axial compressive stress level, such that the specimens with a larger height-to-width ratio and lower axial compressive stress exhibited better ductility.

Static Behaviors Test Research on Precast Concrete Inorganic Insulation Sandwich Composite Wall Panel with Four Sides

Flexural Experiment and Design Method of Steel-Wire-Enhanced Insulation Panels

Flexural Behavior of Insulated Concrete Sandwich Panels using FRP-Jacketed Steel-Composite Connectors

Tests on seismic behavior of pre-cast sandwich concrete wall panel with cast-in-site end columns

Bending Performance of Precast Ceramsite-Concrete-Insulated Sandwich Panel with Stainless Steel Shear Connectors

Experimental Study on Seismic Performance of Prefabricated Monolithic Concrete–Polystyrene Panel Composite Wall Panels

Experimental Study of Steel Plate Composite Shear Wall Units under Cyclic Load

Performance of Double-Skin Composite Walls with Re-Entrant Profiled Faceplates under Eccentric Compression

Mechanical behavior test and analysis of HEH sandwich external wall panel

Mechanical performance of prefabricated lightweight steel-foamed ceramsite concrete wall panels: Experimental and theoretical investigations

Axial-flexural behavior of FRP grid-reinforced geopolymer concrete sandwich wall panels enabled with FRP connectors

Experimental Study on Seismic Behaviour of an Unreinforced Precast Wall-Slab Structure Based on UHPC Sandwich Panels

Experiments and Numerical Simulations on the Seismic Performance of Steel-Frame Composite Wallboard Shear Walls

Flexural performance of precast geopolymer concrete sandwich panel enabled by FRP connector

The Shear Behavior of Insulated Precast Concrete Sandwich Panels Reinforced with BFRP

Flexural Behavior of Precast Concrete Wall - Steel Shoe Composite Assemblies with Dry Connection

Simplified load-deflection analytical model for partially composite insulated concrete wall panels under flexural loading

Experimental and Numerical Investigation of Novel I-Shaped GFRP Connectors for Insulated Precast Concrete Sandwich Wall Panels

Experimental Study on Mechanical Property of a New Type of Sandwich Wall

Seismic behavior of steel frame infilled with wall-panels connected by sliding joint

Shaking table tests and seismic assessment of a full-scale precast concrete sandwich wall panel structure with bolt connections