Abstract:The effect of Bi2O3 on ZnO-based varistor ceramic sintered around 800 °C is still not fully understood, because most of the ceramic cannot reach full densification at this low-temperature. Therefore, (balanced) ZnO–0.5 mol% V2O5–0.5 mol% MnCO3–0.5 mol% Co2O3–0.5 mol% TiO2–xmol% Bi2O3 (x = 0, 0.01, 0.05, 0.1 and 0.2) ceramic was designed and prepared by the solid-state sintering at 800 °C. The effect of Bi2O3 variation on the microstructure and electrical nonlinearity of the sample material was studied by using methods of XRD SEM, STEM, EDS and E–J test. Bi2O3 can further activate the reaction at the interface between the V-rich liquid phase and ZnO grains during sintering. This enhanced interface reaction is the key reason to the extremely low-temperature sintering of the ceramic at 800 °C. The variation of Bi2O3 in the 0–0.2 mol% range barely influences the constituents of the ceramic, which consists of ZnO main phase and two other secondary phases: Zn3(VO4)2 and Zn2TiO4. Most of Bi2O3 tends to segregate at grain boundaries. As a result, a soaking time longer than 4 h is needed to allow Bi ions diffusing into enough grain boundaries and improving the nonlinearity of ZnO based varistor ceramic. The sample containing 0.01 mol% Bi2O3 and sintered at 800 °C for 8 h has the best properties of a 43.3 nonlinear coefficient, a 2300 V/mm breakdown voltage and a 0.13 mA/cm2 leakage current density.

Study on the Stability of ZnO-Bi2O3 Based Multilayer-Chip Varistors

Microstructure Design and Optimization of ZnO-Bi2O3-Sb2O3 Based Ceramic Varistors

Microstructure design and optimization of ZnO-Bi 2O 3-Sb 2O 3 based ceramic varistors

Effect of Bi2O3 on the ZnVMnCoTiO based varistor ceramic sintered at 800 °C

Elaboration and electrical characterization of ZnO-based varistor ceramics in different sintering temperatures

Effects of SiO2 and B2O3 on electrical properties of low-temperature sintered ZnO–Bi2O3 varistors

Structural and electrical properties of ZnO–V2O5–TiO2–Co2O3–MnO varistor ceramics with low sintering temperature

Simultaneously enhanced electrical stability and nonlinearity in ZnO varistor ceramics: Role of Si-stabilized δ-Bi2O3 phase

Reliability enhancement of zinc oxide varistors using sputtered silver electrodes.

The Effect of ZnO Powder Particle Distribution on Performance of Multilayer Chip Varistor

Bi4Ti3O12 Modified Low Voltage ZnO-based Varistors: Microstructure, Electrical Properties and Aging Characteristics

The Influence of CeO2on the Microstructure and Electrical Behaviour of ZnO–Bi2O3based Varistors

The Dependence of Sintering Temperature on Schottky Barrier and Bulk Electron Traps of ZnO Varistors

Influence of a Zn-Bi-Sb-O Synthetic Multi-phase on Highly Nonlinear Properties of ZnO-Bi 2 O 3 Varistor Ceramics

Optimization of Sintering Temperature and Doping Level of Cr2O3 in ZnO-Pr6O11-Based Varistor Ceramics

Effect of Minor Bi2O3 Doping on the Microstructure and Electrical Nonlinearity of the ZnVSnO Based Varistor Ceramics

An ultralow concentration of Cr2O3 dopants driven lower temperature sintering ZnO‐based varistor ceramics

Influence of Co2O3 doping on the microstructure and electrical properties of ZnO–Bi2O3-based varistors

Improving Age Stability and Energy Absorption Capabilities of Zno Varistors Ceramics

Influence of Dopants on Electrical Properties of ZnO-V 2 O 5 Varistors Deduced from AC Impedance and Variable-Temperature Dielectric Spectroscopy

Influence of SnO2 on ZnO–Bi2O3–Co2O3 Based Varistor Ceramics