Abstract:Hollow fiber membranes fabricated via dry/wet phase inversion method usually have two dense skin layers,which will increase its resistance of mass transport as a support membrane. It is necessary that the dense skin layer of support membrane has been eliminated to improve separation performance of composite membrane. The excellent. chemical resistance of poly(vinylidene fluoride) (PVDF) to many acids and alkalis has made it as an attractive membrane material, and then it's often fabricated as porous hollow fiber membrane by phase inversion. In the process, the formation of the skin layer is due to the rapid exchange between solvent and coagulation, so many attempts have been made to slow it, so as to control the formation of the skin layer. In this paper, it has been found that the fabrication progress becomes unstable, and the membrane prepared has noncircular lumen, when the "weak" or "soft" coagulation is used. To increase the fabrication solution stability during membrane formation, dope viscosity was focused in this experiment. Dimethyl acetamide (DMAc) was used as solvent as well as internal coagulant, and the additives including LiCl, water and surfactant Span were chosen to investigate their effect oil the viscosity of the fabrication solution. The dope viscosity will greatly increase after adding LiCl, while the variety of dope viscosity is unconcerned in the fabrication solution concentration as adding water. The homogenization and stability of the fabrication solution are improved by adding Span,and the viscosity increases at the same time. Without increasing PVDF concentration, the stability of the nascent membrane was improved by increasing the fabrication viscosity. The PVDF hollow fiber membrane with the structure of single outer skin layer and finger-like pore through the cross-section, has been successfully fabricated. The mean pore radius and water flux of the single skin hollow fiber membrane were greatly improved.

Effect of Glycerol Additive on the Morphology and Crystallization of Prepared PVDF Membranes

Effects of Preparing Condition on PVDF Membrane Morphology

Influence of additives on phase separation process of PVDF solution and membrane morphology

Porous Membranes Modified by Hyperbranched Polymersi. Preparation and Characterization of PVDF Membrane Using Hyperbranched Polyglycerol As Additive

Effect of Additives on the Morphology and Performance of Symmetric Network PVDF Membranes

Effect of Dissolving Temperature of Dopes on the Morphology of PVDF Membrane

Polymorphism in Porous Poly(vinylidene Fluoride) Membranes Formed Via Immersion Precipitation Process

Effect of Polymer Molecular Weight on the Morphology and Crystallization of Prepared PVDF Membranes

Effect of Maturation Time of Dopes on the Morphology and Crystallization of PVDF Membranes

Effect of the Casting Solvent on the Crystal Characteristics and Pervaporative Separation Performances of P(Vdf-Co-Hfp) Membranes

Morphology and Formation Mechanism of Poly(Vinylidene Fluoride) Membranes Prepared with Immerse Precipitation: Effect of Dissolving Temperature

Influence of Solvents on the PVDF Membrane Properties

INFLUENCE OF ALCOHOL-BASED NONSOLVENTS ON THE FORMATION AND MORPHOLOGY OF PVDF MEMBRANES IN PHASE INVERSION PROCESS

Effect of Coagulation Bath Temperature on the Structure and Performance of Polyethersulfone Hollow Fiber Membranes by Dry/wet Process

In Situ Crosslinking of Hyperbranched Polyglycerol in Casting Solutions and Its Effect on the Structure and Properties of Porous Pvdf Membranes

Formation Mechanism and Crystallization of Poly(vinylidene Fluoride) Membrane Via Immersion Precipitation Method

Effect of Coagulation Bath Temperature on Formation Mechanism of Poly(vinylidene Fluoride) Membrane

Controlling the Morphology and Crystal Form of Symmetric Network PVDF Membranes by Bath Temperature

Preparation of Symmetric Network PVDF Membranes for Protein Adsorption Via Vapor-Induced Phase Separation

Influence of Dope Viscosity on the Fabrication of Pvdf Hollow Fiber Membranes with Single Skin Layer

Effects of coagulation bath composition on structure and morphology of PVDF membrane prepared by thermal induced phase separation method