Abstract:The corrosion behavior of the 70/30 Cu–Ni alloy in stagnant, aerated pristine and sulfide-containing simulated seawater as a function of exposure time was investigated with polarization curve measurement and electrochemical impedance spectroscopy (EIS). It was demonstrated that the compact protective oxide film formed on the 70/30 Cu–Ni alloy resulted in the decrease of corrosion rate in aerated pristine seawater; while the corrosion rate of 70/30 Cu–Ni alloy in aerated sulfide-containing seawater increased dramatically due to the catalysis of the sulfide ions or sulfide scale for both the cathodic and anodic reactions. The impedance spectra and the corresponding equivalent circuits confirmed that a duplex layer of a surface film was formed on the 70/30 Cu–Ni alloy in aerated pristine seawater after a period of time and that the inner layer was responsible for the good resistance of the alloy; while only a porous and non-protective corrosion product layer formed on the 70/30 Cu–Ni alloy in aerated sulfide-containing seawater, which made small values of charge transfer resistance (Rct) to last for a abnormally long time by interfering with the growth of the protective oxide film. The composition of the surface film on the alloy in pristine and sulfide-containing seawater for different exposure times were investigated thoroughly by XPS. It was found that the duplex corrosion product layer formed on the alloy in pristine seawater was composed of an inner Cu2O and an outer CuO layer. The porous and non-protective corrosion product layer formed on the alloy in aerated sulfide-containing seawater was a mixture of CuCl, Cu2S, NiS, Cu2O and NiO with trace amounts of CuO and Ni(OH)2 and that the most significant component was Cu2S. In addition, SEM was used to analyze the topography of the 70/30 Cu–Ni alloy in both solutions after different exposure times.

Relationship of Corrosion Product Films and Recrystallization of 70Cu-30Ni Alloy

Characteristics and Formation of Corrosion Product Films of 70cu–30ni Alloy in Seawater

Seawater corrosion of A Cu-Ni alloy in intermittent immersion

Influence of Deformation and Heat Treatment on Seawater Corrosion of 70Cu-30Ni Alloy

PROCESS OF FORMATION OF CORROSION FILMS ON ALLOY 70Cu-30Ni IN SEAWATER

Correlation of Seawater Corrosion and Processing of Cu Ni Alloy Tubes

Corrosion Behavior and Product Film Formation of Ni Co Cu Nanocrystalline Coatings in Neutral Salt Environments

Surface characterization and corrosion behavior of 70/30 Cu–Ni alloy in pristine and sulfide-containing simulated seawater

The Anisotropy Electrochemical Corrosion Behavior of Ni-based Single Crystal Superalloy on Different Crystal Planes: an Investigation from the Film Growth Aspect

Corrosion behaviors and galvanic studies of microarc oxidation films on Al–Zn–Mg–Cu alloy

Evolution Of The Corrosion Product Film On Nickel-Aluminum Bronze And Its Corrosion Behavior In 3.5 Wt % Nacl Solution

Corrosion Behavior of Cu-Ni-Fe-Mn-Cr Alloy in 3.5 Wt.% NaCl Solution

Surface Characterization and Corrosion Behavior of 90/10 Copper-Nickel Alloy in Marine Environment.

Evolution Mechanism of Element Ni on Matrix, Surface and Interface During Static Soaking of Copper-Nickel Alloy

Electrochemical Impedance Spectra for the Corrosion of Porous Cu-35mass%Ni-(5,10)mass%Cr Alloys in Molten (0.62li,0.38k)2co3 at 650 °C in Air

Study of the Corrosion Product Films Formed on the Surface of Mg–xZn Alloys in NaCl Solution

Effect of Thermo-Mechanical Treatments on Corrosion Behavior of Cu-15Ni-8Sn Alloy in 3.5 Wt% NaCl Solution

Corrosion of Copper-Nickel Alloys in Seawater-Based Electrolytes

Effect of Annealing on Microstructure and Properties of Cu–30Ni Alloy Tube

Corrosion Behaviour of AA6082 Al-Mg-Si Alloy Extrusion: Recrystallized and Non-Recrystallized Structures

Corrosion Behavior of New Cu-Sn-Fe-Ni Alloy in 3.5wt% NaCl Solution