Abstract:The microstructural evolution of Mg–2.0Gd–1.2Y–1.0Zn–0.2Zr (GWZK) alloy during homogenization and subsequent aging heat-treatment and the tensile properties of the peak-aged sample at various temperatures have been investigated. The phase transformation during homogenization, static precipitation during aging, and deformation mechanisms at 250 °C are systematically analyzed through XRD, TEM and EBSD measurements. The peak-aged GWZK alloy has good combination of strength and ductility at elevated temperatures owing to its high thermal stability by the LPSO phases distributed along the grain boundaries. The change (19 MPa) in the yield strength of peak-aged samples between RT and 250 °C is mainly related to easy gliding of dislocations on the non-basal planes due to the decrease in critical resolved shear stress of slip. Two strengthening models are applied to quantitatively describe the effect of $${\left\{11\stackrel{-}{2}0\right\}}_{\alpha }$$ precipitate plates on Orowan strengthening corresponding to RT and 250 °C. Ignoring changes in solid solution strengthening and grain boundary strengthening of the peak-aged sample caused by increasing temperature, the calculated reduction value (16.5 MPa) in macroscopic yield strength from RT (based on the basal < a > slip mode) to 250 °C (based on the pyramidal < c + a > slip mode) is in good agreement with the measured reduction value (19 MPa).

Characterization of Phases in Mg–4Y–4Sm–0.5Zr Alloy Processed by Heat Treatment

Effects of Heat Treatments on Microstructure and Mechanical Properties of Mg–4Y–4Sm–0.5Zr Alloy

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Characterization of Phases in Mg-10Y-5Gd-2Zn-0.5Zr Alloy Processed by Heat Treatment

Effect of heat treatment on microstructure and mechanical properties of Mg-4Y-1.6Nd-1Sm-0.5Zr alloy

Precipitate Phases in the Mg-4Y-4Sm-0.5Zr Alloy

Precipitation Behavior and Mechanical Properties of a Mg–Zn–Y–Zr Alloy Processed by Thermo-Mechanical Treatment

Effects of Samarium on Microstructure and Mechanical Properties of Mg–Y–Sm–Zr Alloys During Thermo-Mechanical Treatments

Behavior of Mg–15Gd–5Y–0.5Zr alloy during solution heat treatment from 500 to 540°C

Optimization of Heat Treatment Process for Mg-11Gd-2Y-3Sm-0.5Zr Alloy

Influence of Heat Treatment on Microstructures and Mechanical Properties of Gravity Cast Mg–4.2Zn–1.5RE–0.7Zr Magnesium Alloy

Effects of heat treatments on microstructure and mechanical properties of Mg-15Gd-5Y-0.5Zr alloy

Microstructure Evolution and Mechanical Properties of High Performance Mg–10Gd–2Y–0·5Zn–0·3Zr Alloy During Heat Treatments

Microstructure Evolution of Mg-4.3zn-0.7y-0.6zr Alloy During Solution Heat Treatment

Microstructure and phase transformation of as-cast and annealed Mg–4Zn–1Y alloy containing quasi-crystal phase

Microstructure and Mechanical Properties of Mg–2.0Gd–1.2Y–1.0Zn–0.2Zr Alloy

Characterization of Phases in a Mg–6Gd–4Sm–0.4Zr (wt.%) Alloy During Solution Treatment

Effect of heat treatment on microstructure and mechanical properties of as-cast Mg-5Y-2Nd-3Sm-0.5Zr alloy

Effects of Heat Treatments on Microstructure and Mechanical Properties of Mg–11Y–5Gd–2Zn–0.5Zr (wt.%) Alloy

Effects of heat treatment on mechanical properties of an extruded Mg-4.3Gd-3.2Y-1.2Zn-0.5Zr alloy and establishment of its Hall–Petch relation

Microstructure and Mechanical Properties of a Mg-Zn-Y-Zr Alloy Processed by Thermo-Mechanical Treatment