Abstract:The impact of different spraying layers scheme on gas-liquid two phases flow, heat and mass transfer in the large scale desulphurization tower with four spraying layers was investigated by numerical simulation. The Euler-Lagrange approach was adopted for the numerical calculation and the inter-exchange of momentum, mass and energy between the two phases was fully considered; the effect of instantaneous turbulent velocity fluctuations on the particle trajectories was also taken into account. Dependability of the simulation was validated via actual on-site data. The results show that large vortex region on the upper left of the tower inlet occurs when only the bottom spraying layer opens. But when only the top spraying layer or multiple layers operate, the gas-liquid contact is much greater and the above-mentioned non-uniformity in the flue gas distribution will not appear. The more spraying layers operate, the higher the pressure loss in the tower is. When only the top spraying layer operates, the pressure loss in the spraying zone is twice as much as that when only the bottom spraying layer is employed. In the absorption tower, the highest turbulence kinetic energy region is located in the spraying zone. With more spraying layers are put into operation, the region of high turbulence kinetic energy is enlarged and its value increases also. When multiple layers operate, area-weighted mean turbulence kinetic energy on the 2nd spraying layer reaches to maximum in the whole spaying zone, while the value on the top spraying layer is even lower than that on the 3rd layer. With regard to the heat and mass transfer in the desulphurization tower, no matter what kind of spraying layer scheme is adopted, the location corresponding to the biggest flue gas quenching rate and the location corresponding to the biggest water vapor generating rate are found coincident, which are located just above the upper plane of the flue gas inlet and beneath the bottom spraying layer. The simulation result also shows that the latent heat transferred through droplet evaporation and the sensible heat transferred via droplet heating up account for 87% and 13% of the total heat transfer capacity in the spraying tower respectively, which is in good agreement with the actual on-site water consumption data.

Numerical Simulation on the Characteristics of Flue Gas Flow and Slurry Drops Evaporation in Spray Drying Thionizer

Simulation on Evaporation and Motion of Atomized Droplets in Spray Dry Flue Gas Desulfurization Tower

Numberical Simulation Study of Flue Gas Desulphurization by Spray Drying

Numerical analysis of SO 2 removal characteristics in industrial flue gas desulfurization reactor by spray drying adsorption

Numerical Simulation of Gas-Droplets Mixing and Spray Evaporation in Rotary Spray Desulfurization Tower

Numerical Simulation Of Spray Evaporation Characteristics In Desulfuerization Reactor

Numerical Simulation of Flue Gas Desulphurization by Spray Tower

Simulation of desulphurization wastewater evaporation through flue gas

Calculation and Analysis on Evaporation and Mixing Characteristics of Droplets in High Temperature Flue

Numerical Simulation of Wet Deacidification Process of Sludge Incineration Flue Gas

Simulation Study on Centrifugal Spray Evaporation Characteristics and Process Optimization of Desulfurization Wastewater

Process simulation on atomization and evaporation of desulfurization wastewater and its application

Experimental research on spray characteristics of nozzle and numerical simulation of desulfurization wastewater evaporation

Influence of Flow-Equilibrating Device on Purification of Flue Gas from MSW Incineration

Numerical Simulation of Sludge Dryness under Flue Gas Atmosphere in the Riser of a Fluidized Bed

Numerical Investigation on the Evaporation Performance of Desulfurization Wastewater in a Spray Drying Tower without Deflectors

Numerical simulation of gas-liquid flow state in scrubber of novel centrifugal flue gas desuifurization tower

Modeling on circulating fluidized bed flue gas desulfurization

Three-dimensional modelling of two-phase flow and transport in a pilot centrifugal spray dryer

Numerical simulation of impact of spraying layers scheme on gas-liquid two phases flow, heat and mass transfer in large scale desulphurization absorption tower

Characteristics analysis and parameters optimization of desulfurization wastewater evaporation in a rotary spray drying tower